Arrma Maintenance Guide (Granite, Typhon, Big Rock, Senton, Vorteks) 4x4 3S BLX

Affiliate links:

Social Media:

Here's a step-by-step walkthrough on what maintenance items to check on your Arrma 3S 4x4 BLX. This will apply to the Granite, Typhon, Big Rock Crew Cab, Senton, and Vorteks vehicles.

#Arrma #Granite #BigRockCrewCab

[m.g.]

great video I just got into RC vehicles a few weeks ago. I have very limited knowledge on how these trucks work and run so watching this has been a HUGE help. Great detail in explaining stuff! Just bought Arrma granite V3 3s BLX for my first truck and it is super fun. Now I think I have finally found the channel I need to look after this toy to keep it running its best, After all, you get what you put into something.Cheers Pal thx

[benroseable]

Really good video. I like the way you do your videos as they are simple to follow and provide great useful information.

[JohnLaViolette-rxjo]

During reassembly, I am having trouble pushing the pins in the steering knuckle deep enough in to replace the screws. Any tips? Thanks for the great video!

[GearsMcTinkersome]

Just the video I needed! A new Senton 3S and 6S owner here, about to upgrade the 3s to 6s specs before it's even rolled once. It's a motor, ESC and servo swap out, so seeing you pull the gear box apart gave me confidence on what's facing me.
I've got a clicking noise on my drive shaft when the wheel roll in the same direciton. Spinning independently only sometimes makes the clicking noise. Looking real close, the rear right suspension is weakest, while the rear left is tightest. That's also true of side-to-side play, leaning the car one way, then that. The rear right suspension has a bit more sag and bit more wobble then the other three. The rear left is tightest on wide-to-side. The front suspension seems consistent to itself and is moderate between the rear extremes.

I'm guessing I should tighten the right rear turnbuckle a few twists to nix the sagging. The side-to-side wobble almost plays like a loose rim shifting along the axle. The front wheels have a little shift that seems 'natural', but right rear has excessive comparatively and left rear has next to no side play. I'm glad I haven't run the thing yet.

[ragsixracing]

*when checking motor mount screws, check side to side play of motor shaft*

one of the two times my bearings failed in the stock motor, this is how i found it. if it gets bad enough the spur can fail even though the motor is still working(2nd failure lol)

[TheChad]

Once again, another RazorRC video saved in my RC favorites folder.😁

[JohnLaViolette-rxjo]

I am having trouble pushing the pins back in to the steering knuckle deep enough so that I can replace the screws that hold them in. Any tips? Great video!

[GeloOfficialPR]

Yep ... Maintenance vids are guud .. im here watching for my typhon/SC Arrma

[TonysRcTechboom]

Very nice Bench clean and maintenance brother 👌 all mine are done and cleaned for the winder Hibernation 🦔 and they will be out in Spring 🌞 great tutorial video mate 👍😎👍

[BigCheese]

Nice video. I usually don't go that far with disassembly. Lazy. I went through so many spurs with my BRCC but ever since I cut a hole in my chassis I never had a problem. Let's the dirt get out from motor area. Wish I had done it from day one. Good video

[gillmccuddy]

My granite is all gummed up from driving in sand. I don't know if it needs new bearings or just oil. But I think I need to take apart everything and clean out the drivetrain and differentials

[hbb]

Good stuff as always. Your Granite seemed to toed out on both sides...more than mine anyway. Thanks for what you do.

[staticswitch]

I am new to the this. I have a Big Rock Arrama truck. Accidentally hit the right side tire with a cement curb. Now my truck goes hard right. How do I fix that. I can see the cV is extended just a little. Any help would be so appreciated. Thank you in advance.

[kodak_jack]

Very well done! Do you have a set of screwdriver bits that goes with that screwdriver? It comes with a BIG Phillips/flat blade that aren't too useful for RC work.
Do you think the modular design Arrma uses is that much better than the typical component layout in all other designs? Thanks.

[randall]

Shocks not leaking ! Mine do but they work good and it's easy .

[benlandrum]

Hey Razor RC. Do you know the part number of that little plastic cover you put on the spur gear shaft? I need one.

[escostales]

Is a maintenance guide coming for the TA Rival 10? Bought it recently and would love to see one.

[actZR]

What kind of hour interval should we do an extensive maintenance like this? Provided its all normal driving conditions, no water.

[theonetazman]

Thankyou so much. This helps astronomically.

[Νικόλαος-οδ]

Where did you bought the screwdriver and the keys?