How To Adjust Your Arrma Typhon 3s Slipper Assembly - Works On Most Arrma 3s Models

Buy one here:

I was curious as to how many turns out this method actually sets the slipper. I took it apart to access the slipper assembly several times after doing this method. The slipper is actually set at 1 full turn out when the wheels lock up. You can still crank the screw down one full turn with the assembly in your hand

Check out the RC Element Podacst here:

The RC Element Instagram

The RC Element Facebook Page

The RC Element (Heli Edition) Channel

Check Out Our Motorsports Channel!!

[markg]

Best video on this issue I have seen! I just melted my rear center driveshaft on my brand new 4S Kraton. First run on grass only 15 minutes. All signs lead to loose slipper.

[ArtietheArchon]

thanks for this video, using the drag and hold technique on a completely different vehicle but it's still the easiest way. I guess the surface you drag across will determine how tight your slipper is

[nlamar]

Thank you for making a quick to the point video... This is a great technique to properly set load on slipper assembly.. great job!

[RCRoads]

Thanks for sharing. The manual isn't very helpful but this video is. The 3s Arrma line is a snap to work on when you know the tricks. You make it look easy and removed the driveshaft like a pro. Great video. 👍👍

[anthonyjones]

Good video. I thought something was wrong with mine because it doesn't roll as easy as vehicles with a center diff. The noise it makes made me think something was broken.

[SebastianLong]

Lol. Guess I should have looked up this video when I was making adjustments to my slipper. I bought a Typhon 3s used and it didn't come with the manual so I was playing it by blind eye. I have 16 RCs and all come apart differently but I took the Typhon slipper out in a similar way to all my other RCs. Didn't realize that adjusting the slipper was that easy. I've only used it twice thus far. First run broke the cheap "aftermarket upgraded" shock shaft. When the guy sent me the Typhon, he also sent all the spares and parts that were swapped out so I just rebuilt 2 stock shocks just to run it. The second run the slipper had come loose and ended up pulling the top of the diff case off to try to get the trans out. Lol. What got me doing it that way was a lower skidplate was installed and didn't realize there were so many screws under it, After I seen how everything came apart, I realized I took way more apart than I had to. All I would have had to do to remove the slipper was one screw on the bottom, pull out the trans tie in bracket and lift the clip and pull forward. Now I know I wouldn't have even needed to do that. Lol. At least I know how the entire rear end comes apart now which I hadn't known before.

[eskimojoe]

Awesome video
My typhon started making a clicking noise after a rock was on top of my center shaft.Ill try this fix

[MidCoast]

Great vid man, it was quick and easy.

[ImTMBR]

Thanks for this helps loads easier going to take it apart haha

[linou]

I got an aarma thyphon .but what is it for ?what impact on the car? Thx and have à happy newyear

[alexanderdavila]

I love rc cars and helicopters and planes

[brianu]

When you say turns out form locked. Do I turn the screwdriver? Or roll the car? I’m lost

[krashkingrc]

Awesome video excellent job definitely easy very smart

[yonicozac]

In my experience setting it this way is way too tight. When the wheel stop spinning you are fully tighten it. I like to set mine 2 turns open from fully locked

[maximx]

What a cool video, you have to subscribe right away.

[ukfieldninja]

Picked up one of these typhons. I changed the arms to RPMS but now when i roll it forward and back by hand it crunches and feels like it doesnt want to roll foward but will with a little bit of force... cant figure out why it doesnt roll smoothly.

Kind of wondering if you knew any videos where i might be able to figure out how to fix.

[SerJeepRadiocontrol]

Buen video amigo!! me gusto mucho!!😜😜 +1 a muchos les vendra bien amigo!!

[scottm]

Im not a big fan of setting it this way..the stock setting in the manual is 1 and half turns from fully tight . .I tried setting it the way shown in this video and i ended up stripping my rear diff within the first battery pack..how I set it it now is I just pop the power module out real quick and without disassembling it at all I hold the spur gear to keep it from spinning as I tighten down the slipper completely then back off accordingly. .1.5 turns from fully tight with new slipper pads seems to be perfect. doing it my way at least you know exactly how much it is set from fully tight.

[vesentearsiaga]

After 5 years already you should have been already big you need to do what the people want I want to see your YouTube grow I want to see videos like you did with your daughter like them type of videos outgoing pulling stuff them videos are cool.

[vesentearsiaga]

I've been here for a long time since you did the skateboarding video with RC cars. I want to see more videos like that at parks skate parks I want to see bashing and stuff like that. To be quite honest all these reviews and fixing stuff is kind of boring.