Engine warning alarm codes for Df Suzuki Df 100/115/140

When engine RPM limiter kicks in , it means ,something important is wrong with your engine . limiter does not allow rpm above 3000 rpm. Oil chang remider makes beeping sound and oil light stays on solid . pull the kill switch 3 times in 10 sec to reset the oil change remider . long beep means you completed the task.

[boashna]

Oil chang remider makes beeping sound and oil light stays on solid . pull the kill switch 3 times in 10 sec to reset the oil change remider . long beep means you completed the task.

[arthurmcmahon]

I have suski 175. Boat ran fine both trips out so far but did get the rev limit and low oil pressure alarm. Oil levels are fine and not leaking any place

[boashna]

You just saved bunch of money and this is not even a Geico commercial . You can buy me a coffee or beer to celebrate your achievement by pressing thanks next to like button .

[StephanadoBethel]

Hi I have a df250 Suzuki outboard not going past 3000 rpm but if I hit the trim down button it speeds up can you assist in anyway thanks

[rayvillalonga]

Good good video my brother, where can I send you some money ? You are a good explainer

[joelielomarable]

Hello friend, I have a question for you. I have a suzuki 225 2010 that for the first time I had a problem. When I turn on the key, its beep is low and when I turn it on it does nothing, but on the tacometer it shows the Ck engine flashing 4 times, it pauses and flashes 2 more times. In your experience it could be those codes that it shows on the screen.

[veselinjovanovic]

Hello friend. I have DF140, and the problem is that RPM slowly drops from 5000 to 2000 after just 10 minutes of driving. After starting it up again, the same thing happens. Any suggestion! Thank you…

[vw]

Hello. I have a problem with my DF 115. Today I started it and just about a minute later it started to beep intermittently, but without turning on any indicator lights. ? I can accelerat without problem but the intermittent beep sounds. Do you know what it could have? Thanks.

[ramziibrahim]

I have a problem with my suzuki 115hp..the light code is 6:3 means O2 sensor.anybody can help me to solve my problem?can show me where the sensor O2 is placing

[finecrazygunz]

Df140 what if it beeps and stays lit and stops beeping but light stays solid

[scottcarter]

I was out yesterday (2017 DF115 with 800 hours) and got the flashing check engine light and a single group of 6 audible beeps, repeating. The flashing light is not following the beep code. I was running at 4200 rpm and I slowed and it went away after a few minutes then came back and then went away. The RPM stayed up so it was not critical. Cannot seem to find out what it means. Ideas??

[lemon]

Pls help my df140 a has a check engine warning light flashing 9 + 1 nobody seems to be able to tell me what the problem is even after service …..
help!

[dimitarmilev]

Suzuki DF40 2007 Check Engine lamp flashes 3-1 times or 1-3. What does he want to tell me? Where is the problem? Help me ! pls :) cuts out and smells like gasoline :(

[wangkurt]

hei my egine .df 70, 98
. dont show tot ouer and bip every 7 sec, no code all fine .3500 rpm

[scottallways]

I got a 2017 Suzuki DF 115 Two things happen that water in the gas in neutral it blinks I was able to find out I had a problem with my fuel vent was taking on water . fuel cell fixed it went away second thing I had happen I sucked a trash bag into the intake didn’t know it I was at high speed traveling and Boat went into limp mode on me then I got the manual out I shut the motor off I tilted the motor up and saw a trash bag on the intake I removed it set it back down about 25 minutes later start it Up no problems codes went away drove off nothing happened it was good to go

[boashna]

Buy a book for that engine .. no such code 1-3 0r 3-1

[StephanadoBethel]

Hi I have a df250 Suzuki outboard not going past 3000 rpm but if I hit the trim down button it speeds up can you assist in anyway thanks

[StephanadoBethel]

Hi I have a df250 Suzuki outboard not going past 3000 rpm but if I hit the trim down button it speeds up can you assist in anyway thanks

[StephanadoBethel]

Hi I have a df250 Suzuki outboard not going past 3000 rpm but if I hit the trim down button it speeds up can you assist in anyway thanks

[StephanadoBethel]

Hi I have a df250 Suzuki outboard not going past 3000 rpm but if I hit the trim down button it speeds up can you assist in anyway thanks