How To Set Decking and Timing | KTM 85 SX - Nihilo Concepts Tool

Nihilo has developed a Stainless Steel Deck Tool that is a fraction of the cost of the OEM special tool. The OEM tool retails for over $94.00 while the Nihilo Concepts tool is only $14.95. The stainless steel is durable and strong and will last for many years. Nihilo uses a water jet to precision cut each tool. The water jet assures that they are exact copies of the OEM specification and will work on your bike perfectly every time. You must have this tool to properly set the deck height, timing and power valve on your bike if your head is not set up per factory specification you run the risk of stator failure and will have an improperly tuned motor.

GASKET SET CPL. 85/105SX 04
Part# 47030099100

47030035020 CYLINDER BASE GASKET 0,20MM | As Required

47030035030 CYLINDER BASE GASKET 0,30MM | As Required

47030035000 CYLINDER BASE GASKET 0,50MM | As Required

Click Here To Subscribe To Our Channel!
Follow Rocky Mountain ATV/MC On Social Media!

[sethmillhorn]

excellent video. simple. to the point. thanks

[AdioShu]

Thanks this was just what i was looking for to understand decking.

[taavetuiga]

Hello
How to configure 2019 KTM 85sx Powervalve with Nihilo Powervalve Adjustment Tool?

[MrCyphermonkey]

Just about to change the piston on my lads 85.
Good video, I just think this is over complicating things, I’ve never had to check deck height or adjust ignition on any of the about 100 basic piston changes I’ve done over the years on all brands of bikes and two stroke engines haven’t suddenly become more complicated.
If you’re doing more that just a straight like for like piston swap yes check it, but don’t fret over it otherwise.

[ИванШелахов-хъ]

Hello, I from Russia, nowhere not can find the key for invoicing ignition, podskajite please, how many millimeters there is on your have

[jacobaugustin]

If this is the first top end on bike can I just use the same size gasket even if it's a vertex piston kit? Thanks

[justincolvard]

When placing cylinder base gaskets Do you place them with the silicone side up or down per one gasket or two

[dasatom]

Hello, I need your i have the same engine. My new piston come's minimal to high in the Zylinder. Do I need to change that.

[ThePhoneMenDotCom]

Hello. where can i get that decking tool? That sure is a clean bike, I need to do i full rebuild, lower and top, I pull the top and the rod is locked up and can't move on the crank, bought the bike used and locked up, I'm going to fix it, looks easy if ya have the right tools. one ting that is hard is torquing the cylinder nuts, you can only get on 3 of them.

[Enntiä]

How many millimeters the timing tools height is?

[hreindustries]

if you use the stock gasket thickness every time you do a rebuild shouldn't it always be the same? How could it change?

[johnnyappleseed]

Do you still have to check this on a piston that isn’t domed?

[DjRay]

Is this only specific to the KTM or does this apply to all Japanese two strokes.

[svenomick]

how many degrees btdc is the timing is it the same for all two stroke thank's

[Mikethephoneman]

My 06 ktm 85 does not have a gasket on the front of the cylinder where the exhaust valve bolts up . Just the red joint sealer is this normal I cant seem to find a gasket for it.

[landlockedviking]

What's the wrench your using to put the cover back on?

[jonfyfazan]

Exhaust valve adjustment ktm 85 sx 2018-2019 ?

[detrinasaunders]

I need the tool used to set the decking and timing in this video

[bryceb]

Wait, so when the pistion is below the tool, the decking is too high and its the opposite when it hits the tool. Wtf, why do they have to make it confusing.

[dbdb]

hi i just buy a ktm 85...i was told it was put in a shed and when took out it wouldt run the kick has a small bit of commpression but can push down by hand and when trying to jump it it just locks up...i tink it mite need a piston kit but i just wanted to know if the timing could be the problem