How To Install A Moen Shower Faucet - Step By Step - D.I.Y

Amazon Deals:

[kenduda]

You are a lifesaver! I took this damn thing apart and I couldn’t figure out how to put it back together. Your video was spot on! Well done sir

[chucho]

like most of your other comments here, I bought a brand new house with everything being installed reversed, your video was straight to the point and VERY helpful, after using my shower either extremely hot or extremely cold, tomorrow my family will bask on the ideal temperature they deserve. THANK YOU SIR!

[Ed-lwxf]

It appears my valve body wasn't recessed in the wall far enough, I have a 1.5 inch gap between valve handle and escutcheon, now what any suggestions? Thanks great video

[jg]

Very simple, very direct, very clear, very helpful. Thank you.

[ronaldpaterni]

Thanks! I’m trying to diagnose why our Moen faucet valve is sticking. This unit has almost identical components, and same tools to install/repair. This video goes into great detail.

[AlbertoOlivares-rosv]

Everything looks good and the instructions I will highly recommend to drain the water into a bucket first before install showerhead so all the residues are in water line goes to bucket not to the new shower head filter… you will see yelllowish water and some small particles first, then clear water will appear thank you

[jackfitzgerald]

My faucet handle was installed incorrectly. This video helped me fix it correctly. Thank you!

[benjaminhaase]

Thanks, dude. I was missing just one screw. You figured it out for me!

[tonyk.]

Thanks, had a stem go bad when some sand got into our water system this helped me remember the config for the handle. Also if you have hard water and you are replacing the stem I had to use CLR and scotch bright to clean inside valve body before the stem would fit in even with the included grease. Nice vid thanks again sir.

[atlas]

Straight to the point. No BS. great! Thanks!

[danielhewitt]

Hi. Thanks for rhe video. Quick question, does it need to silicone caulk?

[T-warf]

Thanks for the video, we did not know about the temperature control in are new faucet, in are new house and we had very little hot water.

[steelewheels]

My plumber didn't install the plaster ground so the valve sticks way out from the shower wall. What do I do?

[aandjmom]

My escutcheon screws, yes they are long. doesnt screw in. They just slip right through the hole but nothing to tighten. the whole valve set came in one package.

[scottperkins]

Exactly what I needed, thanks! I had lost my directions thank you one thing: you really have to tighten the adapter screw down hard -I was afraid I was gonna break the plastic but I kept going until it was tight.

[gradysockwell]

Thanks for putting this video out. Instructions from Moen aren't the easiest to follow.

[deecochin]

Thanks for the video. I am installing a similar Moen Alder 82603 shower faucet and have a question. As you know the trim ring has a red mark on the left side for hot, and a blue mark on the right side for cold. When I turn the handle to the left (it only turns in the left direction) cold water comes out, not hot. As I turn it down, around the 6:00 position the water starts getting warm as I would think it would, the further I turn right hotter the water gets as it would make sense until the knob stops turning around the 1:00 position. Is it correct that cold water comes out first not to get burned? And if it's correct cold water would come out first to the left, why would Moen mark the trim ring red for hot instead of blue for cold?

[btexpress]

Good instructional video. Don't understand the negativity.

[torcan]

That was so simply explained. Thank you!

[chungvan]

You did not explain why leave the white plastic limit stop piece should be at 2 o'clock vs 12 o'clock position on the valve handle? Your video looks like at 1 o'clock position. What's the difference? Does this make it more hot or less hot at 2 o'clock position. Please advise before I do my install. Thank you for the great video!