Multi-function DC/AC 5V - 24V Forward Reverse Motor Controller Timer I053A02

How to set the Forward time, reverse time, stop time for all function, setting the time, setting trigger and demonstration. The module is from ELETECHSUP. You can set the minimum time to 0.1 second and maximum time can be set to 9999 minutes or 166.65 hours.

The best thank you for me is to not to skip ads and Subscribe 🔔 to my channel, like 👍 the video It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe and enable the bell 🔔.😊

Jump to different section of video by clicking on the time:
00:00 Hardware explained
-02:21 How much current this module needs?
04:45 Power save mode settings
05:35 Module settings
07:25 Reverse Time settings
09:00 Setting STOP time
--10:55 1 is 0.1 Second, 2 seconds, 3 is minutes
11:05 wiring Explained
12:51 F-11 Setting and Demo
18:11 F-02 Setting and Demo
20:21 F-11 Setting and Demo
22:21 F-12 Setting and Demo
23:31 F-21 Setting and Demo
24:27 F-22 Setting and Demo
25:07 Trigger setting (option 9) Falling edge or Rising edge
26:13 Conclusion remarks

Purchase this item:

Tutorial by Ahmad Shamshiri form Canada
****************************
****************************

Get other projects code and learn Arduino

**** AFFILIATE PROGRAM ****
#robojax #robojax_timer

[jw]

At 14:30 he glosses over the loop function, for anyone wondering. Function 8 is the number of cycles.

0=Loop forever
1-99=number of cycles to loop

Hope this helps others, I've seen quite a few comments about the looping function.

[KenCharlesMX]

Great explanation and the few things missing are available in the comments. You sir are a legend!

[nirmalmaan]

Amazing video. Helped a lot with my son's technology project. We ordered this from Amazon but didn't receive any programming instructions. We tried for many days but we could not figure it out. My son was so frustrated and we were about to return it, but we came across your video and it was a lifesaver. Very Helpful. Thank you so much.

[dangruen]

REPEATING (LOOPING) PROGRAM: Several people have asked how to set the board to repeat the cycle automatically. Essentially, parameter 8 sets the number of times to repeat, 1-99. 0 means repeat indefinitely. Default is 1. I found a clue to this in a table I found by googling "canton electronics Model IO52B02". Instructions there are a good supplement to what is in this video. (Shoutout to jw11432 who also addressed this in his comment).

[alexn]

Very awesome, informative video. I’m doing a little project and needed this little board. You explained everything so well it literally took me 5 minutes to set the whole thing up. Thanks a lot my friend.

[robs]

Usually I hardly comments but I salute you for this video thanks

[pjm]

Thank you for posting this! It was very helpful.

[anupshekhar]

To be frank the video is really nice and I liked the way you have made and explained settings . I wish you could help your viewers with their doubts rather asking them to watch the video again. Questions they hv asked were not covered by you in this video

[PradipDoleyJonai]

Sir how to setiing use linear actuator forward auto backward and stop

[namtr]

One of the best overview and review videos I've ever seen. Where have you been and why did I not find you till now. Sub'd

[tkomic]

it would be great if they had something like this w a simple wifi

[DasFelixx]

Thanks. Worked welll for my project :)

[goosphil]

Hello Ahmad, and thank you so much for your comprehensive video. I looks so difficult for me. I am looking for a module to trigger a linear actuator. In fact, I just need the function F-12. By chance, do you know if a simpler module that does just that exists? When the linear actuator arrives at the end of its path, there is an internal switch that cut the power. So, my idea is to set up the time for the same length as the linear actuator, so, when the linear actuator arrives at the end of his path, the module will cut the power and wait for the reversed trigger. Am I right?

[patrickkirby]

Thank you for this helpful video. Can this unit be programed for two different stop times?

[LestersCustomTrkShp]

Great video! Where can I get a copy of the instructions you showed, on the AliExpress page, that can be printed out?

[raknin]

Great video.
1. If one cycle of f01: t1 t2 and t3 completed in order to activate it again i need to diconnect the 5v power and connect it again?
2. If i want to do one cycle of f01:t1, t2, t3 and afterward want to start a new cycle of f01:t1 do i need to be program it again?

[RichRocketMan]

Can this be used to control an actuator in the same fashion? Actuator extends for specific period of time, then pauses for specific period of time, then reverses direction for a specific period of time. I would be looking at a 12 volt actuator arm. Thanks!

[tylerjmechem]

Hi! Great video! Can this be used with an 110V 750W 1HP Sewing Machine Servo Motor? And can you suggest what wires and trigger to use to initiate a forward, stop, reverse cycle?

[bacuba]

la ripetizione ciclica (8) funziona solo con F-01 e F-02 e non funziona con F-11 e F-12, pertanto non sarà possibile in F-12 comandare il numero massimo di ripetizioni. cerco di spiegarmi se volete che un attuatore avanzi per x volte comandato dall'impulso del pulsante non funzionerà. infatti in F-11 e F-12 manca il numero di impostazione 8.

[astropacc]

I’m planning on using 2 of these on funtion 11 one for each 100w 24v dc motors each motor will be moving in the opposite direction at the same time of day how can I trigger this to work on a timer I want it to open curtains at a set time of day then close them at a set time
Thank you