How to use JB Weld

In this video, I show how to use JB weld to fix a broken transmission case.

[Rickfyoutube]

Fixed my smashed oil pan on my 05 Sunfire with JB Weld. Great product. Like he said prep/clean surface.

[minecraft-shower]

dude i broke the joint for the clutch handle on my crf 150 2009 honda bike, and it seems like jb weld will do the trick! thank you so much

[karensok]

This is the exact video I needed to watch. Thank you.

[gaz]

Yep jb weld is great stuff.
My bro used this on his motorcycle engine side casing that was cracked.
He gave it a good key inside and used it on the inside and is still perfect after 4 years.
All that high heat as well from the engine and it still don't leak.
I use it all the time and used it on the exhaust and is still there after 6 months.
The smell can come into the car though when the exhaust gets hot but you can slap gum gum exhaust paste over the jb weld and it solves that problem.

[TheIdleCrow]

I got a lawn mower that was left outside. I was bored decided to get it to run. and I did but the thing spat out oil.

oil tank clearly took water already knew this cause it was a pain to get all the water out.
but did not see a crack that was likely made in winter when the tank likely filled up and froze.

since I got the thing to run I'm going to try to seal the crack with this!
looks like it should work as long as it can handle heat and heavy vibrations.

I'll find out! this push mower was nicer then the one I've been using so worth it.

[teslarawks]

I tried using JB Weld on my sending unit on my 2002 ford taurus SE and the gasoline turns JB WELD into a rubbery solution after 5-7 months. Today I have a transmission case with a hole in it about the size of a side of a zippo lighter from buying CV-Axles on eBay. Too stiff and no lock ring and knock it pretty good and I was wondering if there is pressure in a transmission on the passenger side 3 in from the CV Axle seal.

[johnwright]

Did the job weld hold on the transmission and did you use the industrial strength as I'm having that done next week.

[Manuel_Z_Kayaks]

I never put anything that needs mixing on paper or anything porous because the paper will absorb some of the chemicals. Go to dollar tree or a kitchen supply department and get a stack of those flexible cutting sheets, wax paper or an old plastic cutting board. I also clean the area well with acetone. sometimes scoring the application site helps the bond too.

[Gushers]

Did i miss the part where you should clean the living hell out of the spot your about to apply it? :)

[OVI-Wan-Kenobi-]

I'm surprised the bolt didn't get stuck in there as it was curing

[harryoakley]

For a job like this, regular JB weld would have been much better than JB Kwik Weld. Also it's an untidy repair. He should have wiped the excess JB Weld off immediately.

[hellborn]

i have the same problem for my power stearing pump bolt hole but i dont have the missing piece

[Santaji]

Would this type of fix work submerged in hot oil? Like inside an engine oil sump?

[rickj]

Will this work on a leaky boat to stop the leak?

[jackslater]

Does anybody here know if JB Weld would work on thermostat housing studs? I (slightly) stripped a thermostat housing stud while replacing the thermostat in my car. I say slightly because it'll still screw in and you can't move it, but when I put the nut on and tighten it, it'll pop right back out. I really can't afford to buy a new head and don't really have the time or skill to take the head off and re-thread it.

[minecraft-shower]

i only heard about jb weld so i didn't know how to use it

[specializeder]

Not pretty but in an emergency a great product.

[rkaztaw]

No wayhosey :).. You will need to weld with alu stick bro. No other way sory..