How-To: Install Holley’s Easy Level Fuel Sender

Holley’s new Easy Level Fuel Level sender uses LiDAR technology for simple and accurate fuel gauge readings. The Holley Easy Level can be used with most electronic aftermarket gauges, including the Holley Pro Dash. Set up is a breeze, just measure your fuel tank depth, hook it up to your gauge, push a couple of buttons, and done. Learn how to install Holley’s Easy Level from the pros at Detroit Speed.

Learn More:

Follow us on social media:
1. Instagram: @HolleyPerformance

[kslvlkdfhkvhkfviwehbhjhj]

I am so glad I found this video. I have been having a terrible time getting my fuel gauge to read correctly. Thank you!!

[nicks]

I wait longer than the 8-10 seconds they recommend in the instructions. Waited a minute before jumping to the next step. Talked to Classic Industries(maker of the sending unit, not Holley). They said it could react faster on the gauge display(Holley 12.3 Pro Dash)than the actual sending unit to respond. Always had the issue of it showing empty when it was a half tank. So far its working as it should. But time will tell.

[x]

Why don't you Holley people answer the questions?

[gmans]

Huge Thanks. I have been frustrated with my ol' Float Style Sender for a long time now. Just need to come up with something cool for the Gauge side of things now.

[wickedjoker]

I wonder if they make something like this for Motorcycles . This would be amazing if it where smaller to fit a motorcycle tank.

[callofgeorge]

anyone have issues with this in an aluminum tank? mine works fine out of the tank but shows empty when installed. curious if the shiny aluminum finish is the issue. going to try calibrating it installed in the tank and may scuff the bottom under the sender with scotchbrite pad and hope the filter does it's job.

[CRazy.CAnucK..]

Can anyone confirm this will work with a terminator x max with a holley 7 inch digital screen?

[rocksrocks]

Holley, it wasn't "easy" the thing always looks past the last 3rd of the remaining fuel and quit working after one trip when I pulled it for the 3rd time to see why it wasn't reading the bottom 3rd set it up on the rig I made to set it up, looked as if it was correct put it back in the tank, and still wont read the bottom 3rd. so I decided to use a fluid to re re ... set it up, I set the empty volume in my test stand looked at my gauge to verify empty and the led was off, zero response and stuck on 1.4v output. Now I have to re install the old sending unit good thing I didn't through it away.

[lloydlewis]

Will these work with Dakota Digital gauges?

[brettbeez]

Will this work in a tank where the factory fuel pump sits within the fuel sending unit? How would one go about installing a fuel pump with out that?

[brantgonzalez]

Issue, my 90 integra has a long ring and not bolt holes, so I'd have to make a new hole and put bolt holes to be able to use this?

[raymondpadilla]

does the tank have to be flat like a fuel cell?

[TheCobrajet]

So are you calibrating this wile you have a physical empty, half and full tank?

[bobtomica]

Can this be used to other universal fuel gauges?

[lucasthompson]

Surely it works with the Holley analog style and CAN gauges?

[Whippdf]

Does the kit come with a template so it can be mounted in any tank? Would this fit in a foxbody tank?

[BrianSmart]

Doesn't work with Autometer fuel gauge.

[Thunderstruck]

So this will work with a Ford factory 16-158 ohm fuel gauge?

[xbgtjg]

does it have a insulation boot, would have to short out the + wire, also do you wire the + wire to your ignition on so it only has power when car is running only

[avshunmeckaneck]

Indicates correctly (1/2 tank) when tested 7in away from a surface outside of the tank. Indicates empty when tested 7 inches away from fuel inside the tank. Why does it work differently on fuel than on a solid surface?