Fuel Injection cleaning in less THAN 5 MINUTE/HOW TO clean injection Directly without disassembling

#ALIMECH #injection #cleaning

In this video, i will show you how to Clean the fuel injection in less than 5 minutes Directly without disassembling any injections, it will be direct injection cleaning by connecting carb cleaner can to injector rail, and staring up the engine BUT keep in mind to remove the fuel pump fuse or the fuel pump wire harness, because we don't need fuel pump to push gasoline, the fuel line is disconnected, carb cleaner can connected instead with an adapter

Half of carb cleaner can can give you best results, and if you of you do it with the whole can, even better

🔔 Hit the bell next to Subscribe so you don't miss a video!

lets be friends
--------------------

**If the video was helpful, remember to give it a "thumbs up" and subscribe and turn the notification bell on, so you dont miss any new videos

[lisalohand]

My husband did that on our truck from your old videos and engine light turned off 💃, thanks Ali mech

[tlfromva]

Worked great and smoothed out acceleration on our 2016 Subaru. Thank you!

[tabonnick]

Amazing video. Simple, Short, Clear.

[Karmaswitnss]

You’re amazing sir, thank you for sharing your knowledge! It’s an awesome trick to know!! My bf wonders how I’m so knowledgeable about working on my Jeep but he never listens to my answers which is watching other people in YouTube. 😝

[chrismarin]

I wish my injectors were that easily accessible.

[prabhakarrao]

There is absolutely no problem with this procedure and mostly works but if you have the time and money it is worth having them ultrasonically cleaned. Believe me you will really appreciate just how much rust (if any) and varnish type dirt comes off the injectors after an ultrasonic clean.

[stevew]

Great video mate. Well explained and simple.

[MrCroky]

Great video and insight into this issue. Thank you ! Just subscribed :)

[Snarkapotamus]

That fuel pump was amazingly accessible! Most are not that easy to get to. I guess the other option would be to find the fuse for it and pull it...but honestly, pulling the rail and replacing them is not all that hard to do.

[alphaomega]

My question, where did you get the long plastic straw thats attached to the spray can nozzle ? The one that came with the bottle is like 3/4 smaller? Did you make it or bought it?

[kennedy]

Can you pull the fuel pump fuse out? It would be much easier than disconnecting the wires.

[barnes]

This seems good for injector rails that are a pain to remove. 👍🏻🤙🏻

[johnarnold]

Just use Sea Foam in the gas. No need to take anything apart. Works great in the fuel and oil.

[ghrezakhoshdel]

درود.. بعد از اینکار شما حتما باید یه فکری واسه تمیز کردن کاتالیزور بکنی... پیروز باشید.

[meaculpamishegas]

I think it’s the ether in the carb cleaner that can damage plastics and rubber, the metal will be fine, but on the other parts stick to mass air flow sensor cleaner

[genericdude]

How well does this work on a V6 and V8 engine? I haven't looked real close at the V6 but the V8 has a hose that connects 2 rails (left bank and right bank). I did try this on my V8 but didn't see any improvement in LTFT. I thought about running another can of carb cleaner but I'll decide on that later. This is the first time I have done a cleaning like this on my original OEM injectors (22 years old - 81, 000 miles). I don't have any codes so it probably didn't need to be done. The only downside to doing this "in place" cleaning is that you don't get to see if all the injectors are adequately cleaned. I'll have to try this on my V6 and see what results I get with it (60, 000+ miles) - they've never had this kind of cleaning done either. Thanks for this alternative to pouring injector cleaner into the gas tank.

[josephhaupt-cw]

How does it affect the catalytic converter?

[LeKelsor]

Would this work on an 8 cylinder motor?

[FenrirsBite]

Will adding lacquer thinner to the gas tank help too?

[craigiefconcert]

I used your method of removing the fuel injectors. Actually I got some spare ones and a fuel rail from the junkyard. Then I was able to pressurize the fuel rail with carb cleaner and I didn’t have to fit the hose to each injector.

Can you do a video on using seafoam or water in a vacuum line to clean carbon? My car is 25 years old and I can see carbon on the pistons when I look through the spark plug holes, but I can’t tell how much there is.