GE Dryer disassembly and reassembly

This video shows the basic steps and disassembling and reassembling your typical GE dryer you'll find in many homes.

[bcope]

Clear, concise and thorough. Just what I was looking for.
I appreciate your efforts.

[gavindmello]

Thank you for this video! I was able to replace the front bearing and get rid of the constant grinding noise. I was going to call a technician but I’m so glad this video helped me do it on my own 👍

[NYdrivingfool]

THANK YOU!!!! This is a very informative DIY. I watched a video a few months ago and he did not explain in detail how to reassemble the front and top I didn't have the left side replaced properly.
I was worried about lint build up. Again, thank you, I reassemble the dryer within 15 minutes without cursing, LOL.

[fitzguineavision]

Thank you for this video, this allowed me to take apart my dryer to find out my drum gliders needed to be replaced along with the piece that they sit on.

[MrElchalo]

This video is really helpful, it explains what you need to do in a way that is really easy to understand. Thank you.

[psycobone]

Couldn't find a video of how to take the lent trap off because it had no screws, so I just did it this way and it worked out good getting all the clogged up lent out of there.Now I see how easy everything is also !

[peteroehring]

This looks like my dryer so this video is a great help. I need to fix a grinding noise. Dryer is only a couple years old and already has problems. Used to be that a GE product would last for years before servicing.

[andrea.gardner]

Thank you! I was able to replace the belt and the pulley. I needed help from my daughter when reassembling but we got it all set!

[markterrance]

Great video, after watching others I was still confused about routing the belt, great explanation

[mikebrown]

You are a lifesaver. Your directions were simple. Belt and tensioner were a little tricky though.

[GeeMoney]

The drum spins while its empty. But when i put wet clothes in the drum doesn't spin? What did i do wrong. This video helped me all the way from start to finish. Best one i found on You tube.

[AdamNovicki]

Ok. The video is helpful to an extant. 2 things people should know.
1) some models have a screw that holds the tensioner in place, so no trying to hold it
2) If you disassemble the left side wall and pull it out towards you, the entire pulley motor is accesible. You don't have to try to pull a new belt from the front.

[johncampbell]

Hey there, This is an informative Video, That being said, It over simplifies the method of installing the drive belt, I recommend, With the drum removed the Idler needs to be wired to the vent pipe to hold the tension while the belt is placed on the motor pulley then once the belt is in place and the idler lined up a person can cut the wire.

[cherylmann]

Excellent directions. Senior female going to attempt a new belt.

[ahstchr]

Bless you. Your video was exactly what we needed.

[rick]

Thank you very much for this video. It answered all the questions.

[donaldwebb]

Very easy to follow instructions simple at it's best

[chrisjeffers]

Thank You Thank You Thank You Thank You Thank You ! Mission Complete

[donavonbrown]

The dryer in the video looks exactly like my dryer except for it doesn't have the 2 little screws inside the door there that secures the top panel. It doesn't have any screws on the front but the only thing I found is a square opening on the top front side and when I look up in through the opening there looks like there is some sort of yellow cross shaped thing up in there that looks like it might be what is holding the top panel down on the front. But it is very difficult to get to even do anything. I know I won't get a reply back in time so I'm going to assume that this is what I'm looking for and I think I'm going to make a video of myself figuring it out and I will share it with you after. Lol

[tguf]

Thanks for showing a great view of the belt dissasembly and assembly! Definitely the tricky part of this dryer. Much appreciated!