Throttle Actuator Service Toyota Tundra 2000-2006

This is how to properly service your throttle body actuator and plate on a 4.7L V8 Toyota Tundra between the years of 2000-2006. Anyone can preform this repair and save a loads of money! This was performed on a north American vehicle however, the international versions should be really similar if not the same.

*Disclaimer: Please use all safety precautions

[videotracx]

This video shows exactly what I needed to get my 2004 Toyota Tundra running again. My thottle body actually looked like it wasn't very dirty. It must have been much-needed cleanup that was not visible. I highly recommend this being done. It can be done completely in about a hour and shorter time if all the tools are laid out in advance. The cover is good to put parts in. Some people like to replace the screws, bolts or nuts so they don't forget where they go. Personally, I've lost them trying that, down on the motor somewhere never to be found. Thanks for the awesome information.

[superfly]

My 02 tundra v8 throttle body is a bit more complex to remove. Good video regardless...
Thank you

[theshootingbench]

This video is for a post July made 05 to 06 2UZFE 4.7L Tundra and Sequoia. This is the updated engine that went in the first year 2nd Gen Tundras. At least in the US.

The title should be corrected to reflect that. If this an 00 to early 05 Tundra or Sequoia then it has been engines swapped with a updated engine.

[RungAtATime]

This is an 05 or 06 engine with the drive by wire/electronic throttle control. 2000-04 Tundras have still have a throttle cable. You also skipped showing clamping off and disconnecting the coolant hoses.

[mfalme]

Thank you for the video, very straight forward and I was able to follow through on my Sequoia. But after all that the idle is so high and I don’t know if there’s any reset or calibration to do.

[doehunter]

Thanks for showing me how easy this is.

[kevinkillion]

Thank you for the input. I was back on the road in an hour.

[ko]

Jeez what’s with all the trashing of this video not fully providing the exact info you want. How about be happy he posted it? If you can’t figure out a socket size let someone else work on your car and watch Mr Rodgers instead.

[pedroortega]

Thanks for your video and help, i need to do this today with my tundra truck 2005..

[dylskee]

I know this is an old video and I'd like to thank you for it, helped me quite a bit. I do have a question though, is there supposed to be a gasket between the throttle body and the air intake? I didn't see one on mine but I noticed they sell a gasket for my 2005 Tundra with the 4.7l V8?

[antientdude]

Thank you for your I need to do this today..

[chrissalinas]

is the Throttle Body Actuator in the same spot on a 2001 Toyota Sequoia?

[rajahani]

so nice neat and makes job easier for us.. thx alott

[danriver]

Thank you for the video, i did the cleaning and after install all back, the engine is 1500 rpm all the time, i run a few miles but nothing change, is there anything else i need to do to set the rpm lower? if you can help us with that info would be great. thank you!

[mannys]

Throttle body cleaner is safer to use. The rubber shaft seals as well as plastic pieces and the electronics inside won't be harmed by proper throttle body cleaner spray, and it won't remove the coating some TBs have applied to the inside.

[flavrdPnut]

Will this help with a P1126 code for the magnetic clutch malfunction?

[VinniePepperoni]

I’d of wiped the junk off the top outside of housing while I was in there, was that a oring seal between those two sealing surfaces or nothing at all where you unbolted that thing from ?

[raygarcia]

Thank you for your very helpful tutorial I really appreciate it.

[michaelreaves]

I have a 2007 Toyota tundra 4.7 liter trd series and have a vibration in it like when you hit a rough spot in the road but when i give it gas it stops

[PapiChulo-ybiu]

I cleaned mine on my tundra, now it kinda shakes a bit and my RPM are at 500 did i do something wrong??? Previous to this it didn't shake