How to Use a Wire Stripper? #VEVOR #VEVORdiyproject

VEVOR Wire Stripping Machine | FREE US SHIPPING ✈
🔴Coupon Code: VVFANS （Save Extra 5% Off）

***********************************************

Connected with us:

👍More Giveaways, activities, deals on Instagram and Tiktok, stay up to date...

***********************************************

About VEVOR
VEVOR is a leading brand that specializes in equipment and tools. Our goal is to ensure that the tough equipment and tools you are looking for are at the lowest prices. Let VEVOR make your job easier and more enjoyable.

***********************************************

This machine is easy to operate and convenient to carry, can process single core copper wire, twin cores copper wire.

Operation

1. Comparing the wires’diameters with the feeding holes on the machine, feeding the wires one piece at one time. Before feeding the wires, please cut off the head of the wires, to avoid gaps caused to the blades.

2. On the output side, if the cuts on the wires are too deep, please check below points:
①Please adjust the handles on the input side, screw down or lose them. (M12 handles)
②Check whether the wires on the right position as you feeding them.
③Make sure the blades are sharp if not, polish them with the oil stone.

3. On the output side, if see the plastic(PVC)has been stripped, but the copper wires can not be disgorged, please check below 4 points:
①Polish the axis of the upside with the oil stone.
②Check whether the springs are loose, if yes, screw down to make them tighten.
③The diameter of the wires are too small, please adjust the space between the two axes to 0.3-0.6mm.
④If the wires you want to strip are hot, also can not get the copper wires stripped out.

4. If the wires were blocked in the axes, please check below points:
①If the springs on the press wheels are too tight, lose them.
②There is too much oil on the cables/wires, please wipe it.
5. If the blades tilted:
①Check whether the center adjuster was loosed.
②Centering adjustment and adjust the screws of two sides of it.
Note

Make sure the wires’diameter is similar to the feeding holes, large wires in large feeding holes, small wires in small feeding holes, flat wires in flat feeding holes.

***********************************************

【Why Choose VEVOR?】
• Premium Tough Quality
• Incredibly Low Prices
• Fast & Secure Delivery
• 30-Day Free Returns
• 24/7 Attentive Service

#VEVOR #vevortools #electrical #electricaltools #wirestrippingmachine #VEVORdiyproject #diyproject

[vevor.official]

🔴Coupon Code:
VVSOC to save $5 off
VVIPSOC($10 off over $200)

[مصطفىالعبادي-ضف]

Is there a delivery service available to God Iraq?

[eternalbatteringram]

What is the red cap or plug for that comes with the extra blade ?

[roshni]

Is this machine only electric machine or we can also use manualy?As the handle is also showing in the video.

[jameskoehn]

Great machine but it comes with no instructions, it's pretty straight forward tho. One thing I can't figure out, it comes with this RED SCREW PLUG THATS VENTED . I CAN NOT FIGURE OUT OR SEE WHERE IT GOES 🤔

[kerbsidemotors]

Running an electrical contractors I thought I would pass comment.
Deliver was very fast with zero notification it was arriving. It arrived in a wooden packing crate.
Initial thoughts there is no allen key for gearbox fill plug-but your have one to fit red vent plug (couldn't see any instructions for red plug or oil grade to top up or change later.
Typical cheap start stop switch with emergency in neutral - reversed this and motor wiring.
There are no stuffing glands or cable retention on stop start button and centre terminals loose in box.
Various loose fixings thread locked.
Not sure on handle on rotating machine 🤔
Test run it could be better than clarke branded Chinese tools-just a bit of quality control and thought so it will pass a pat test.
Similar issues with other Vevor products-tinkering to get to uk standards

[buckerooney]

It's not as good as this makes out to be.