SKR 1.4 - TMC2209 with Sensor less homing.

This is a brief tutorial on how to install TMC2209 UART with Sensor less homing on a SKR v1.4 3d printer board.

SKR 1.4 Playlist:

One Time Tips, You Can PayPal Me:
Discord:
buymeacoffee:
Twitch:

Hardware:
1 - SKR 1.4 Turbo
1 - TMC2209 UART v1.2
1 - NEMA 17

Amazon Affiliate Links *** Paid links ***

BigTreeTech Github:

[minimaldp]

I really don't know how many times your videos have helped me but honestly, it is a bunch. I really appreciate your work.

[warsimph]

You saved me so much time and effort!, i followed a tutorial for upgrading my Anycubic Kossel Plus with this board but it just didn't work, turns out i missed the INVERT_X_DIR for the motors, after noticing that detail everything worked, thank you for yout simple and complete step by step, really nice video!

[kemsing]

On the latest V3 TMC2209 drivers the jumper position under the drivers for UART is different. I just wasted 3 days trying to figure out what was wrong. I was getting an "all low" error all the time. The older drivers have the jumper on pins 5 and 6 counting down from the board side, on the V3 drivers the jumper goes diagonally between pins 2 and 6.

[brianfoster]

@Ed's 3d Tech Thanks. This was easy to follow and understand. Have you done any work with closed loop drivers?

[eddale]

how do i fix an usb error on the upload? And my pc doent see my 3d printer. if you can help thank you

[Maaxdledesma]

Hello, how can I be more precise? Because my motor Y vibrates when it prints slow

[Vizenzo]

When you want to run the TMC2209 in stand alone mode on for example E0 and Z0, do you need to bend the pin on the stepper driver and keep all the jumpers in?

[hobbyone]

hello .... do you have any idea why my CR10S, after putting marlin 2.1, prints all the layers always on the first one?!? the Z axis does not want to be raised during printing .... in homing and in bed leveling everything is fine but during printing it does not want to know ... ideas? I mount the BigTreeTech SKR 1.4 Turbo with TMC2209 drivers. Greetings

[cemguley]

Hi Edward...I have Skr1, 4 turbo board and 4 x DRV8825...I could only adjust the Z axis...the other homing not working correctly...Can I adjust sensorless with this stepdrivers...

[mustafaonurucak]

Merhaba
Her şeyden önce, iyi şanslar
MKS SGEN L V2 Anakartım Var
Marlin Firmware'i USB Üzerinden Bu Karta Atarken Hata Oluştu.
Ek olarak, bellenimi SD Karttan yanıp söndükten sonra, PID'yi Repetier Host'ta ayarlayacağım sırada sensörlerden sıcaklık değerini okuyamıyorum.
Yardım ederseniz sevinirim.
İyi günler

[maxkremmel]

I have a MKS TMS 2209 V2.0 drivers. Do they also work on the SKR 1.4 Turbo? Can't find any instructions to that.

[ThStriker]

So you power the board with 12V and connect it via USB to the computer at the same time?

[nuudelbuuvei]

Hello.
I have a 3D printer from anycubic S.
Recently replaced motherboard with skr,
but I can't get the all axis endstops to work.Driver is TMC2209
Pls tell me🙏

[dragnet]

So you don't have to connect the endstops on the board?