QMV TDR12V2 Time Delay-Off Relay - 0 to 60 Seconds

QMV TDR12V2 Time Delay-Off Relay - 0 to 60 Seconds

QMV TDR12V2

#timedelayrelay #qmvfasttech #12vrelay
Standard automotive style relay
Adjustable time delay 0 to 60 seconds with internal potentiometer
10 amp / 15 amp rated contacts
SPST - Single pole Singlethrow
Low 1volt (1k Ohm) trigger voltage
Unit includes: 12 volt time delay relay

Get your QMV Merch today!
#qualitymobilevideo #installations #caraudio
Instagram: @qualitymobilevideo
Twitter: @qualitymobilevi

[JerryFulton-os]

Rodriguez Shirley White Deborah Taylor Sandra

[brujulaaladeriva]

220v motion sensor and N555 module, DIAGRAM

[FrankBuisRoyalPressAmsterdam]

Hi, is it possible program this timer 0, 3 seconden ?

[PrafuljrathodRathod-gzsi]

Mereko 5 nomodyul chahiye kitne ru mileg

[novasigma]

I have my cars underglow wired into my cars DRL as it's the only source that will allow the cars underglow to turn on when I unlock the car, I'm looking for some sort of switch that when turned on will start a countdown to turn off, ie the 12v ignition turns on the countdown timer and turns off when it's counted down

[ThejasierYaotsu]

What type of relay do i need to make (Follow Me Home Headlights) i need a relay which will receive the signal from the door being locked/unlocked and can stay on for about 10 seconds which can signal the headlights relay switch to turn the headlights on

[nyvinchenz]

So if put a push button switch to turn the relay on it will be like a key cycle and will charge the item im controling for the amount of time i have it set for .. well how about if i put a momentary switch if i hold the switch longer that the program time will it stay on or turn off the relay just make sure . I using it for a hydraulic clutch launch control silonoide. Just want to make sure it full disengage just incase he mess up and hold the momentary switch during the track run

[HermannJelinek]

H ey Danny Iam locking for a circuit diagram for the Timerprint QF1021A/B V1.5a thanks Hermann

[danrosslf]

Hi, can this be used to delay the dome light of a car? and will it turn off if the key is turned to ignition?

[Babu.]

Can I use only one second one suddenly off?

[MM-kxpj]

I’m looking to disconnect the negative wire of a cb speaker for 3seconds after I unkey. Will this work? Does it send voltage out of the relay?

[MrSeth]

I need one that can go off after 15 minutes.
Can I set this module to 15 minutes?

[Chinosaez]

Question: Can this relay be latched back with power to the contact using the open contact that when energized with a trigger will maintain the circuit with 12V. The trigger itself may be pulsating but once stops pulsating the trigger and the latch will continue until the timer is done and drop off the power and whatever else I'm powering with 12V?

[matthewlett]

Will this unit be able to be used fr a turn signals on a home made trike that I'm wiring up

[paulgee]

Hi is this compatible with use of a 12v fuel priming system

[BeeBait]

I am trying to make a DIY lightsaber.

The two spools will hold the blade material, and when the button is pressed, or switch flipped the motor will spin and push the blades out.

Can I use this to make sure the motor only spins for a second, on enough for the blades to come out but no further spinning of the motor?

Also, can this somehow work with a DC motor? I'm not sure what's optimal to drive this system, as it will be chain driven, or gear driven, with bidirectional capabilities in order to retract.

[bhargavroy]

How to increase the delay for one minute

[thediscoman]

so could i have a simgle wire on the output that would heat up on startup to burn some polesterine

[Lyle_]

Would this be recommended for creating cornering lamps on a vehicle? Once a standard on Lincolns & Cadillacs, (activated by the turn indicator, to remain on a few seconds after turn indicator stops)

[onedayatatime]

Hope you can help! The wiring on my car is damaged and will cost more than it's worth to fix. So what I was going to do was connect to a power source that turns on with the key, then connect to a start button, and then to the starter relay. I was thinking after the sixty seconds the starter could not be engaged by accident. so I was wondering what the power output was or if it was passive. I have already ordered it but still two weeks before it arrives so i am mapping out all the safety switches I need so that is why I was wonder about the power output.
Thank you