Liberty engine 2

My attempt at building the liberty engine but can't get it to work any suggestions most welcome kind regards...

[dadlymalose]

My Brothers
If you don't do leave it don't discourage people in need don't come to just listen or look and keep quite
This thing worked for me
❤
Thanks My man who come with this
Just do your calculations on Coil and it will work for you and your Family

[McFlysGaming]

I got this from AI
If cost is not an issue, and the silver content needs to be more than 75%, the composition of the alloy for the perpetual electricity generator rotor could be adjusted as follows:
- Silver: 85%-95%
- Aluminum: 2.5%-10%
- Copper: 1%-4%
- Zinc: 0.5%-2%
- Nickel: 0.5%-2%
- Magnesium: 0%-1%
- Titanium: 0%-1%
- Beryllium: 0%-0.5%
- Silicon: 0%-0.3%
This composition would have an even higher silver content, which would provide even greater electrical conductivity than the previous composition. However, it's important to note that increasing the silver content beyond a certain point can also reduce the mechanical strength of the alloy, so this should also be taken into consideration.
Again, the exact composition will depend on the specific properties and performance required for the perpetual electricity generator rotor, but this provides a general idea of how the composition can be adjusted to increase the silver content.

[_LanSolo_]

It is indeed the SEMh71-2C from Cantoni & C Milano Motor.
2780 RPM
0.75 HP
0.55 KW
3.6 Amps
etc.
Your Motor has segnificant lower RPM.

[mustafademirbas]

Does it really work? What are your expoerience?

[McFlysGaming]

Your magnets is one piece, you need to copy exactly the way he put the magnets on the rotor. Don’t try to improve the device until it is running correctly. I’ve subscribed because I want to see this gen run. I want to do this but I have no funds to burn. Looking forward for the next video.

[McFlysGaming]

The motor he used was from Poland SEMh71-2C. Also look into Robert Adam for more detail.

[damo]

Nice job 👍. What metal is your rotor made out of?

[_LanSolo_]

A friend of mine is currently building the Liberty Engine 1.0. For this another motor was used with 2800 RPM and 0.75 HP.
He thought the Liberty Engine 1.0 has a simpler design which is easier to maintain and copy. I agree with him at that point.
Could you please give us details about the neodymium magnets u are using?
He ordered 30x10x5 mm N52 magnets which can hold 8.2 kilo gramms each just to give it a try. Therefore it might be necessary to adjust the suspension via pully to reach the 220V..

[krismarc]

that it doesn't work if we don't make the rotor with the special alloy. The rotor is the heart of the machine.

[EF-Electrics]

Saw your uploaded videos, big efforts made so far congrats. Are you sure you checked:

> correct orientation of the magnets polarity used? (North, South)
> use only one opposite pair of wound coils to power you single phase motor.
> with your setup the rpm of the motor selected should not be less then 1500 (the original liberty was a 2800rpm one)
> perhaps the magents configuration used are too strong, not allowing for rpm to build up .

I hope you succeed . Take care

[johnM-Jr]

when you run it w house power and the motor, how much volts do you get at each winding?

[massimobru]

Ciao, sto seguendo il tuo progetto che tipo di trasformatore hai usato(Tipo)?
Ci puoi fare vedere video sul funzionamento?
Grazie.

[SINANOZYOLDAS]

For 15 years, I have been working with angular resonance and I am ready to do the electricity generation project together with investors who agree to make an official protocol. Everything will be done openly after the signatures are signed.

[peterdiedrich]

Wo kann ich den Kompletten Bauplan bekommen

[danielrestrepo]

Hello brother.. Question, did you get it to work ?

[Mark_Meisho_Thompson]

What metal did you use for the rotor as apparently it’s an alloy/silver mix?

[Andreiy]

Bring the coils closer to the rotor, the speed needs to be 1.5k, you should have results

[SUNRISE.with.NATURE]

Kindly make a hole into the rotor and put a neodenium roundshape magnet and then check it will work, your outer magnets will triger the voltage into the coils but inner magnet and their magnetic field is controlled by Ed current's magnetic field of rotor

[collinking]

your block of aluminum has to be SILVER Aluminum Alloy <Silver has the highest electrical conductivity of all metals, it wont work with just aluminum he states this in the video.

[larsjensen]

Even if I become a member of this channel and pay the highest membership, I don't get any information about a usable free energy machine because of that, do I????