Powerbolt2 Programming

[neri]

Time Stamps
0:31 How to change you master code
1:28 How to add user codes
2:03 How to delete a user code
2:48 How to add a one time user code
3:18 How to enable/disable user all codes
3:51 How to delete all user codes
4:12 how to enable/disable auto lock
4:43 How to change auto lock time delay
5:15 How to mute/unmute lock
5:47 How to reset the lock to factory settings

[waterklosetcartoons]

If you’re having trouble like everyone seems to be, and I was, it’s probably because the lock isn’t orientated right and that part is at the end of the video under factory reset and that renders everything else useless, bad choice to part it at the end. You won’t be able to lock the door or test any old or new codes if it’s not orientated right. Best bet here is to factory reset, reorientate, set new master code, then set new user codes.

[scorpio]

Thank you so much! Extremely useful and easy to follow! Ive been looking for the longest time to find a video like this. Great job!

[wcpendergast]

Followed the steps on adding a user code and when we type in the code afterwards it still beeps red 3 times and won’t unlock our door.

[Gen_Kael]

This thing is a nightmare. Did it step by step. Still unsuccessful

[staceytollison]

I am having a hard time programming the lock, it says it's been programmed, then it falls to work. super frustrating.

[sebastianweaver]

Thank you so much I finally got it to work thanks to your video. With the possible theft scare from a falling out with a friend who has a family history with sticky fingers and the friend knew the code we are now feeling safe again. Thank you.

[michaelkane]

Hello. I have programmed three of these units successfully with zero issue. However, I have one particular lock that does not allow for additional programming features like auto-lock. Every attempt, I get three red beeps. None of the other locks gave me this issue. I am 100% doing what is in the video. Any suggestions?

[dirklance]

ALWAYS make sure you orientate the lock for the correct side first. This will save a world of headaches. Every comment with issues on here can be solved if you do that first. Set up is flawless after that. If something screws up in the middle, make sure to reset it with the button on the back before moving forward again.

[rsstnnr]

Everything seems to work until I try locking the door and then it always beeps three times and flashes red. I've tried going through this 10 times with no luck.

[drtroyturner]

One suggestion is punch numbers slowly. The same steps that work can fail if pressed to fast and vice versa the same steps that previously failed may work if you take a breath between each number pushed. Careful, too slow as in 5 seconds between button pushes will also fair as a protective measure aa the systen will assume that slow pushers are criminals who cant make up their mind.

[lorilong]

hi, this video rocked! one question. I did the auto lock for 10 seconds but cant figure out how to now change it to the max of 50 sec. I tried the steps over and over... still locks in 10 seconds. can you put the exact steps, meaning do i have to CLEAR out the 10 seconds somehow?

[aultraman]

Installing the lock was easy - just took out the old and put in the new. However, programming the lock was not the easiest. It just wouldn't program and gave me the 3 beeps. I reread the instruction - unconnected the cable and then reset. Finally reconnected the cable and got the lock programmed successfully. Seems like that was the missing step for me. My recommendation for Kwikset is to highlight that (the disconnect) in the menu.

[_O_]

Mine won't program at all. Should I restart the whole thing and try all over again?

[butchp]

Thank you I don’t believe the change the auto lock seat instruction was in the box so this helped

[dreehogan]

I wish I had read the comments before wasting my money. its not working

[ilurvemv]

Is there a way to buy a back-up key for the Kwikset Powerbolt 2 lock system?

[carnsolus]

thanks :)
lost the instructions, this helped a lot

(didnt lose the french instructions, but can't read french)

[kickinitwithferney]

Quick question so I have my code and set up, I put my code an it locks but to unlock I press the lock button and it unlocks why is that shouldn’t I have to put the code to unlock again ?

[mohammedrahman]

After programming the code and the lock accepting it, why does it not work? It will lock but not unlock. Why? I've reset the unit a couple of times but to no avail. How do you fix this? Please help!