Washing Machine Off Balance Repair, Samsung

Revive Your Samsung Washing Machine! - How to Repair Suspension Rods. Is your Samsung washing machine acting up? Is it there a loud banging sound coming from your washer every time it goes into spin cycle? Does your Samsung washing machine refuse to go into a high speed spin leaving your clothes soaking wet? It is most likely due to failed suspension rod issues? In this comprehensive video, we will guide you step-by-step on how to repair Samsung washing machine suspension rods. You'll learn the essential techniques and tools needed to get your washing machine back to optimal performance. Don't let laundry day be a hassle any longer! Watch our expert tutorial now and say goodbye to washing machine troubles.

The information provided in this video is for informational purposes only. The techniques demonstrated may not be suitable for all individuals or appliances. By watching this video, you agree that you are solely responsible for any repairs or modifications you choose to undertake.

Please exercise caution and ensure your own safety when attempting any repairs. Always follow the manufacturer's instructions and guidelines specific to your appliance. If you are uncertain or uncomfortable with the repair process, it is recommended to seek professional assistance.

I cannot be held responsible for any damages, injuries, or losses that may result from the use or misuse of the information provided in this video. Viewers should proceed at their own risk.

Furthermore, please note that some appliances may have specific repair restrictions or guidelines set by the manufacturer. It is important to familiarize yourself with those policies and comply with them.

By watching this video, you acknowledge and accept these terms and conditions."
#SamsungWashingMachine
#SuspensionRodRepair
#WashingMachineFix
#DIYApplianceRepair
#LaundryTips
#HomeMaintenance
#RepairTutorial
#ApplianceRestoration
#SaveMoney
#diyprojects
#ad

[gened]

Thanks for the tips. Three things I'd add to this:

1. Perform a balance calibration when you're finished. Hold down "Temp" and "Delay End" buttons simultaneously for a few seconds and when it reads "cal", press start. It takes about 2 minutes to run through.

2. I pushed the right rear rod down the right side at an angle so I could weave the hose around it (from the top end) as I brought it up into position. Fighting it around the spring didn't leave enough room to do it without potentially damaging the hose.

3. Use a headlamp or a helper for the back right. If you drop your flashlight, you'll need monkey arms to reach it. I can't play basketball to save my life, but I can reach high shelves and to the bottom of washing machines (barely).

[thoth]

Just Finished Replacing all 4 Suspension Rods (2024 Upgrade DC97-16350U) on my WA50R5200AW Samsung Washer. They look sturdier. No more Bounce when I push down on drum. We'll see how it washes. Thank You to the maker of this repair video. It was a life and time saver. Don't Forget to Recalibrate!

[IsaacCastellanos-ln]

Bro is a life saver. I do recommend doing this just with two people though. One to hold the lid and only to raise the drum. Tons of grease. It sticks.

[matthewburrell]

Thanks for posting. 30 minutes and $45 in parts. Save me a fortune.

[christophercosenza]

I replaced them in less than 20 minutes and it fixed it. Kept my wife from scraping a $1200 unit. Thanks bud.

[vanessapatman]

Thank you for this video!! I have one of these pain-in-the-butt washers and tried to do this watching half a dozen other videos. Yours was crucial for finally getting the top off. Lifesaver!

[bambambig]

Thank you for the video. I ordered upgraded suspension rods off amazon. This video helped me fix my washer today. Took about 30 minutes

[jasonhess]

I appreciate the help. I was ready to throw my washer through samsungs corporate office windows and now I don’t have to go to jail.

[TheBaitShop]

This was a really fantastic video. Thank you so much for recording and posting it. I have it bookmarked and will check your channel for future repairs! Great job, thanks again!

[aureliomedina]

First time swapping these. The video is well done & concise, followed it step by step, and my washer is working great! Thanks for the video!

[brianloftin]

Thank you for this great video! I caught the “screwdrivers” as well and I love the fact that you were such a good sport about it when it was brought up instead of getting angry. On a tight budget, so I went with Amazon (Tomoon) rods that were highly rated with a lot of positive comments about how they are thicker and stouter than the factory rods. Just installed them, calibrated the machine and spun a huge load of wet towels with no problems. I didn’t cut my arms or hands, either! 🙌🏼 I did wear rubber gloves to take the old, nasty, sticky rods out and lubed the new rods with white lithium. Thanks again!

[jonathangutierrez]

Thank you for the step by step instructional video! I was able to repair my washing machine for $35.

[pcjay]

Thanks for the video, but I have a couple suggestions that should make it easier for beginners like myself.
1. Mention that the metal on the inside is EXTREMELY sharp. I cut myself on the forearm which required six stitches.
2. Take an existing rod out and measure it before you order. I have the exact same model that is used in your video. I used the link in the description to order the rods. I verified that the model number was listed in the description on the Amazon ordering page. The rods that came were just over 26", while the existing rods are 27".
3. Instead of trying to use one hand to disconnect the tension cables (this is where I cut my arm), remove the pack panel of the washing machine. This is done by removing the four screws on the back. This opens up the back of the machine allowing greater access to the suspension cables.
4. Be really careful while the lid is being propped up. If it slips, like it did on me one runs the risk of disconnecting some existing cables. This happened to me and cut the grounding wires (green, green/yellow wire) on the rear left side.
5. Like someone mentioned before, do a re-calibration before using.

I'm bringing these issue up so others don't make the same mistakes that happened to me. I have replaced the rods and the washing machine works like new. Thanks again for the video.

[richmondlotelugukurradu]

Excellent video. This really helped me to fix my washer as many others did.
Greatly appreciate the time and effort you took to show this to us.
W as ame to do it in close to 30 minutes.
👏👏👏👏👏

[babybee]

Amazing, ordered the spring off Amazon came within 2 days and only took me 5 minutes to install. My washing machine is working great now!! Thank you!

[renemedina]

I’m gonna go for it. I’ll comment how it went for me after the fact.
Thank you 🙏🏼

[claireremlinger]

Thank you so much for posting this. I never thought I'd be able to fix my own washer, but your video was so helpful. You saved me hundreds!!

[emmanuelgarcia]

Thanks for the tip !!! I fixed the problem. Happy wife, happy home 🏡 💖 💓 💕 💗 ❤️

[mridulmahajan]

Thankyou so much for posting this video. All of the other videos I saw were total bs. But this was quite simple.

[richs]

I've seen other videos of this repair where the rod ends were greased where they contact the washer, is this nessesary?