how to repair LED bulb 💡 💡 💡 with simple process.....

please like and subscribe my channel 🙏🙏🙏🙏🙏🙏🤝🤝🤝🤝👍👍👍👍👍

[VarunBhargavan]

Check the LED resistance and put that across the LEDs to test them. Don't directly short them. Most of the time, these LEDs are in series, acting as voltage dividers. Shorting one may put too much voltage across the others, burning them out.

[floogelhornzzz]

I have 2 bulbs that were dim. I knocked one with a knife, knocking on the yellow LED squares, to get it to jiggle back into full bright. Once I got that one working, then I tried knocking the other one, but while doing so, the first one went back to dim again. Then while trying to get that one bright again, I touched the knife to a dark part and saw a puff of smoke. Now that one is permanently dark without even a bit of bright. The other one lights up very dimly when I put the two sides of a pair of rubber handle, needle-nose pliers to each LED square like these videos always say to do. But _never_ does it cause to light up all the other LEDs when you come upon the one LED that's defective. On many LED squares they all spark to life but very dimly. I don't know what your instructions are good for. I tried putting the two sides of the pliers on each LED of the first bulb and _not one_ lights up. They all stay dark at all times. So now what?? How do I fix my 2 LED bulbs???

[Locoman]

Thanks for sharing your video ; This is a "short term" fix / solution only but do remember that each LED draws a certain amount of current from the total available current that's applied to the globe, by bridging the gap of the "stuffed" LED - the remaining LED's will get a slightly higher amount of current through them all & their lives will be shorter than that of having all LED's working but by replacing the missing LED if possible - you'll be able to keep it working properly as intended ; the only question is to where you'll be able to buy these small SMD ( Surface Mount Device ) LED's on their own to replace the "stuffed" LED that caused the issue in the 1st place.

[noilorato]

the best video ever. simple, and it works perfectly. do not be afraid withe cable.

[MUHAMMADAMIN-gymk]

Save Better With Charger 5V
That is DAnggerous.. with Only 1 Cable.

[yabinuh]

terimakasih atas ilmunya.. sangat bermanfaat 🙏

[JitendriyaDalbehera-evnn]

How to Repair the LED bulb Without soldering iron please say I AM intrested

[bessiebraveheart]

Nice one, just leave the defuser off, they will run cooler, and the light will be better.

[kshyanapravasarangi]

Bro hum jesa wair le sakte use se bulb repair karne se kuch hoga nahi to

[carlostanael]

Boss paanu pag mahina na ilaw nung mga led kahit hindi nman pundi pwde pba palakasin tulad nung bagong bili?

[mohandasballal]

Just scrapping and soldering the perticular part, is it the proper way to rectify the fault ?

[gabrielirlanda]

Thanks, but what if you have 2 or more leds damaged? will this technique still work? Or is it only if you have 1 damaged led?

[rogem]

Bermanfaat infonya. Seumpama sulit tidur bca halus haillahuwaalhayyul qoyyumlatakhudu husinatuwwalaanaum" berulang2 sampai tertidur, tetanggaku tidak mau bca awal ayat Kursi itu saat sulit tidur saat meninggalnya tidak baik. Bcanya halus tapi jngan terlalu halus. Doa itu untuk pmbca yg islam.

[ssennonojohnmary]

What if fauty LEDs are more than one, how do you carry out test using that method?

[padraiggluck]

The Chinese don’t want folks repairing defective bulbs so now they’re gluing to globes to the base. They don’t just pop off any more.

[justinberry]

Ok, don't do what this guy does. You'll live longer. I promise

[ajaycreation]

Sir ye jo current laga ke check karne se hame problem ta nhi hoga current nhi lagega ta

[deviantart]

If you fixed like that is very dangerous, you can remove first the lamp from AC and then you can search dead led with cable and use battery

[DBPT]

I tried doing this, removing 1 busted led and then soldering it. I tried to use the led bulb but it blinked every like 1min. It scares me it might explode.

[alisharkan]

Bertahana hanya beberapa jam😂, kalau LED yg lama dibuang, lgsg di jumper seperti itu, Jadi led nya berkurang dan tegangan berlebihan.. maka apa yg terjadi!.. usia LED yg lain tidak bertahan lama 🤣🤣🤣.. akhirnya semua led akan terbakar 😂