Paintless Dent Removal Kit Review - Can I repair the dents on my car?

In this video I try to remove a couple of dents from my Fiat 500 with the Super PRD Paintless Dent Removal Tool Kit!

Follow me on Social Media:

=============================
Affiliate Disclosure:
=============================
Some of the links used in the description will direct you to Amazon, as an Amazon Associate I earn from qualifying purchases at no additional cost to you.

[martinamor]

Mostly from what I see from your video, when the puller tool breaks from the dent surface, the adhesive fails mostly from the puller tool surface, resulting in leaving the adhesive on the dent. As a surface scientist, I would suggest firstly you need all surfaces to be clean and free of grease. As the failure is more often on the puller surface I would recommend that you clean its surface with alcohol or even better to roughen it with 240 wet and dry emery grit paper, then wash it with water and finally an alcohol rinse and dry with a tissue dab. That should enhance the adhesion on the puller material. Also with any adhesive bonding, the glue thickness needs to be as thin as possible. When it becomes too thick you will then get adhesive failure, which generally is weaker as it fractures through the glue rather than one of the other 2 surfaces. ie the puller surface or the paint surface. So my advice to you is when the adhesive has been applied to the puller, press it hard onto the dent to encourage a thinner glue line.

[boxxcutta]

His first mistake was putting the dent remover in the center of the dent You want to work your way outside inward never start in the center.and just remember it will be a rinse and repeat cycle until dent is gone

[kellen-KMK]

Thanks for the info. The kit I got had no instructions whatsoever, this helped a lot. 👍🏾

[teedtad]

Take to a professional?! They want an arm and a leg and to empty your pocket to do the job! No way, no chance! DIY or get a friend or his friend who knows the skills! This video was CLEAR to follow!! 💡✅✅💡

[shellster]

We lived through the process with you, willing it to work, because you did keep trying one more time! I have suggested to my husband that he return the kit he bought from Aldi, although it was a bargain 🙂. Thank you for sharing this

[TjD__]

I would recommend getting a Heat Gun or a Hair dryer and heat up each of the dens before you pull the dents. Metal has a memory once the metal heats up it will help with the dent removal.

[marduchok]

heck yeah! I like it when my favorite YouTubers trying a new format. Legit nice car, man!

[brentpolk]

If you let the tool do the job, by slowly using pressure and not just going at it until is pops off; you'd have better results.

[johnboughton]

I have exactly the same kit & if you read & watch the instructions first the results are amazing
We own a fiat Panda & a Landrover Discovery both had been subjected to collisions with Super Market Trollies and all 6 were pulled out successfully the only thing I did that they didn’t show was to warm the panels with a hair dryer I just thought correctly that a warmer panel would pull better & it did
I was very happy with the results & for £9:99p it was well worth the money just remember to read the instructions & watch the video & use plenty of glue! I hope this helps & saves you money

[nasapayrollsystem]

I minute is not enough ..mine says 8 minutes to cure .. then try

[markthorne]

Good video I've just brought similar kit .I've watched lots of videos with guys who do this for a living and is a long process to get really good results. Given that they are using professional tools.

[annab]

Thanks so much for your vid . I’m an older Aussie lady and I bought this kit off our Aussie Amazon . It came today without any instructions. A little bit annoyed that it looks like it’s going to take a lot of effort to get any results. 😕But I thank you for your honest review 🙏and I’ll give it a go when I have time 👍

[albertoascari]

I like tapping them out then sanding, filler and paint..of course depends on the size, small bullesye dents are best done like this..I think the slide hammer version is better. I've broke a few of these as they cant stand the strain of pulling to hard on a dent..Pro paintless removal isn't that expensive and they use tools that go behind the panels and do a very good job

[Mr_Fahrenheit]

I would apply the glue on the front of the pad a run it around to the back of the pad, also you cleaned the car panel but not the pad, this could be why the glue sticks to the car better than the pad.

[stevio]

It was helpful to get me started... Better than the instructions manual. The comments are useful too.

[KINGBONES]

Used the same kit today, 1 heat up dent then apply the glue 2 i let it sit for 10 minutes , it wasn't perfect but most of the dent was gone,

[teedtad]

Good tips! Well explained! Bravo he finally got it!! 😅🙂😊😊

[alfa]

Paintless dent removal, from the inside, might have got both perfect (aside from the scratch). Interesting vid.

[HungNguyen-ggxe]

Good luck with the way you are performed.

[peterrossbooth]

Interesting video. Having a blast in the week 🙌. Thank you!