K1 MAX Removing the Top Frame / Gantry ... HOW TO Creality

This is a quick Video in how to remove the top frame anf gantry , as requested by the community.

removing the top frame supposedly easier if @Creality3D actually added 2 access holes at the back pannel to remove the top frame faster and easier.

I did cut 2 hols in the back pannel to have faster access to the top fram upper screw .

If anyone have a better / easier way pleasse share it in the comments .

🛠️ This is not your typical review; instead, we're diving into the challenges head-on, addressing each one from its unique perspective. The D3vil Design team is hard at work, pushing the boundaries to extract the maximum potential from this 3D printer.

🌐 Stay connected with us on Discord for more updates and to share your questions:

Don't forget to like, subscribe, and hit the notification bell to stay in the loop on our 3D printing adventures! 🚀🔧 .

non-affiliated link :

Sponsors links

Special Thanks to LDO for the continouse support @ldomotorsjason3488
----
Huge thanks for @triangle-lab6335 for helping me in the development and experements along the years
----
and to @bigtreetech5117 for sponsoring
----
My Original OT Hotend in collaboration with TriangleLab:
----
My Belts and Idlers ( In collaboration with Powge ) @POWGE_official :

The full Kit of belt and Idlers: ( K1 and K1 Max )

D3vil Belt alone

D3vil Idlers alone
------
NOTE: We are not sure if this will void your warranty or not, and we hold no responsibility if you choose to follow our tutorials, so do it at your own risk .

i dont think this Videos will ever be recomended or sponsored by @Creality3d

#creality #crealityk1 #crealityk1max #k1 #k1max #3dprinting #tutorial #repair #fixed #3dprinters
#omranello #3dfuzz #3difinity #3d #nozzle #toolhead #disassembly #service #3dfuss #extruder #fix #tpu #OT #OTnozzle #OTHOTEND #hotend

[danielb.]

Ha, I did disassemble mine yesterday 😀, I'll post some pictures and comments later, great job mate as always 👍

[yamsahaa]

Very interesting, how do you tension belts please? I just received my k1 max and i think belts are too tight. Tanks for sharing

[printermandarwin]

This week on Pimp My K1... Can you add nitrous oxide to the hotend? Let's find out.

[Alex_M_Creations]

Have you found an extruder to replace the factory extruder? I’ve noticed that the second version I received has already failed and the same issue is happening again and I can’t use a washer to fix the issue sadly.

[KG]

LED cable was going out on its own for me ;)

[mati]

It would be nice, if somebody would make some risers for the K1 and K1C, for the chain to clear the frame.

[TheSmileCollector]

Life saver! Sorry but this sounds like a dumb question but I'm curious if you can make a better guide on how to properly level the bed.

[KG]

I wasnt able to even print the 17 minutes benchy because of layer shifts so I dissasembled everything now.. The right front idler pulley has a lot of play, while on the left side it is tight. Will you design those parts also? you know the front parts where only one pulley is sitting.

[exakelgaming]

it would be nice if someone modelled a frame extender that has all the right holes to fit the gantry.

[acethrashin]

hey are you planning on replacing or adding linear rails instead of the linear rods. cause ive seen someone on reddit do it and it seems it makes it more rigid and quieter and less ringing on faster speeds. just curious if you are

[danavogel]

any chance there is a gantry square print for this? i get very good prints but precise parts arent printed very acurate on both my k1 max's (i think its slightly unsquare)....my 2 bambu printers print parts that just together lol....any other tips or knowledge would be awesome too.

[faiyezjabbar]

Dear Omran, Assalamoalaikum.

Recently, my printer had an error where the nozzle hit the bed and dragged itself, damaging the build plate.

That was not as big a a problem as the print now being skewed on the X axis. Squares become slight parallelograms. off by 1 degree maybe.
How to fix this? People are saying it's belt tensioning issue but could it be a problem of a bent frame?

The prints used to be perfect before that incident.