How To Install Parking Radar Sensor System

In this video I will show you how to install a rear parking sensor system in your vehicle. The installation will require you to remove your bumper and drill 4 holes, but the system does perform very well and can help with your parking. The sensors are very accurate and will give you an audible alert as you back up your vehicle. See link below for tools and parts used.

Wire Length Info:
The sensor wire is 8' long (connecting to the controller box).
The display module wire is 16' long.

======
Buy Parking Radar System (Choose different colors in listing)

Car Panel Removal Tool Kit

Angled Push Pin Pliers

DEWALT Right Angle Attachment

Auto Ranging Multimeter

Automatic Wire Stripper

Professional Wire Stripper

Crimping Plier Tool

100-Piece Magnetic Screwdriver Set with Rack

Wire T-Tap Connectors

Insulated Wire Butt Connector

Cordless Drill Driver 20V

Screwdriver Set

======
Shop Dial2Fast Store For List Of Tools & Parts

Support Dial2Fast on Paypal

Shop Amazon

Try Amazon Prime 30-Day Free Trial:

========
As an Amazon Associate, Ebay Partner, and any other affiliate member, I earn commissions from qualifying purchases with the links provided here.

[andreamiller]

This was such a great instructional video! You did an absolute superb job explaining and showing everything clearly! Very much appreciated!!! Kudos to you!!

[tonynovosel]

ill be doing this installation on the exact same vehicle tomorrow and before watching this video was not confident....however NOW! after watching your very detailed instructional video im full off confidence and would like to say....THANKYOU VERY MUCH FOR A VERY GOOD DISCRIPTIONAL VIDEO!!!!

[stevebutler]

Great idea putting sensor at the rear so it can seen from rear view mirror ALSO Saves a lot of time and faffing about
Tracing the cable to the front on the car

Many Thanks Very Clear explanations
Steve Butler UK

[thomascherian]

Very clear and detailed video. Great work

[biribiri]

Can't thank you enough for this! I just bought a 2000 Honda Accord with a dead reverse sensor. Planning to add an aftermarket reverse sensor and the one that you showed fit the bill!

[mickmack]

Thanks for the great video. I actually installed the viewing module inside the driving side pillar directly behind the driver. As I play music and don't really need to see the screen, just hear the beeping. Cheers. 👍

[rafbay]

Best DYS video ever, well done and totally straight through - 20/20

[christravels]

This was a really great video! Thank you

[Jubjubz-lebg]

Best DIY video on this subject man, made me confident enough to start my install👍🏼

[pavittarsingh]

You done very professionally work thank you your video Mack my work so easy for my sprinter van

[fotomedia]

2002-2004 Honda Odyssey rear sensor Installation is a little more tricky but still similar to the one in this video. When drilling your holes for the sensors you'll need to avoid the inner reinforcement steel beam directly behind the plastic bumper. There's no need to remove the rear bumper completely but I highly recommend to at least peel back the plastic bumper by not removing the bottom underneath fasteners so you can see where the holes can be drilled, . The two center #2 & #3 sensors will end up being a little further apart than recommended about 27 inches apart . The two outer sensors #1 & #4 on both ends won't be a problem to clear of the inner steel enforcement. Also, the back-up light on the older Odyssey models is in the lift gate so it's going to require some extra wire fishing to get the wires to the inside of the Driver's quarter panel. Be expecting to take a good afternoon to complete the job.

[pickeyism]

Thanks for sharing! Well said “the toughest part of installation is drilling holes to bumper”. 😂

[ASURAN]

Thanks for showing the green line. It helps with my reverse parking assist project with my Prius C!

[PauonYT]

Bro thanks for this tutorial! Masha Allah!

[YourHomeTorontoRealEstate]

This is really my favourite Channel!
Thanks for your nice Videos,
it is very enlightening,
Waiting for your latest update.


Dunlop Park

[sushh]

You are very good at making instructional videos.

[rodovikusa]

thanks my brother very useful video, I will get for my car for sure, I will make a video too, installing it to motivate others and stop damaging cars around.

[joseanderson-cuff]

Excellent video, well edited and informative.

[selly]

Exelente muchas gracias por tu gran explicación.. gracias

[weepingangel]

Thank you. I am installing 5% tints on my rear windows (old car) so I need sensors to reverse. Thank you.