Drill Bits For Drilling Plastic Acrylic Plexiglas Perspex Laminate Smooth Clean Hole No Cracking

Drill Bits For Drilling Plastic Acrylic Plexiglas Perspex Laminate Smooth Clean No Cracking. Here is a video on how to properly drill through acrylic plexiglass. Thise drill bits eliminate the need for a Polit hole you need to drill a small diameter pilot hole to get started. The steep 60 degree angle gradually goes up in drill bit sizes until you reach your desired diameter.
Please Click The Subscribe Button Below And Share Video With G+, Facebook, Twitter and all Your Favorite Social Media!
Comments and questions are encouraged but please be respectful.

Disclaimer: Do not try this at home! Any content seen here is for entertainment only! Do Not try anything seen here yourself or there may be danger of bodily harm or legal consequences for your actions! Any illegal activity is prohibited and Wayne Winton and or Tri County Locksmith Service are not responsible for your actions!
Wayne Winton, © 2014. All rights reserved. Publication, reproduction or distribution of this film by any means whatsoever - including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world — is strictly prohibited without the prior written consent of Wayne Winton. Please note that Wayne Winton, Tri County Locksmith Service does not state any confirmed facts only personal opinions. I am not directly affiliated with any of the vendors or manufacturers in this video. Wayne Winton, Tri County Locksmith Service is not liable for any damage or loss through the use of products or techniques shown - Use at your own risk! This film and the Wayne Winton, Tri County Locksmith Service film series broadcast on YouTube is intended for entertainment purposes only.
Tri County Locksmith Service
1338 Grand Ave
Glenwood Springs
Colorado
81601

[additudeobx]

This video reminds me of those commercials where the person is obviously trying to make use of some item or process as difficult as humanly possible to use as a comparison to the advertised product.

[MoosesWorkshop]

How come your not supporting the pieces under where you are drilling?

[ien]

Drilling plexiglass elevated is like the worst thing ever. That empty space you drill through open to a lot of crackling. You should always drill on a flat surface and start it slowly.

[vcrpnff]

why are heck are you drilling with the acrylic elevated? put it on a flat surface, then drill, and you'll minimize cracking. it's the same with wood, which avoids deformation and more perpendicular holes.

[hughcouvopoulo]

rotozips great for making large holes in plastic .nice product great vid to

[simbp]

I can't tell if this video is just trolling us? Assuming not, this video should be labeled "Worst technique to drill through anything".

[Mason-Dain]

$8 worth of information vs $1000 kitchen table nice man

[jeffmoss]

nice one Wayne, those look really nice.

[winningorlearning]

This test should have been done on a drill press in my opinion

[thewhitemustang]

This is like a saturday night live skit.

[PapaGleb]

Great video Wayne. Thx for the new bit tests

[pinnacle_moto]

Are you not supposed to support the underside of the perspex with wood to prevent the splits? Plus looks also like you are putting allot of pressure onto it. Take your time.

[mibukobooks]

Best thing of all is the table underneath. He's going to ruin it soon.

[XellosMetallium]

Wish I look this up before I use a Soldering Iron. I see some minor cracks around the holes after I scrape away the melted plastics.

[garygooch]

Title should read
"Plexiglass drill add"

[lettuce]

Wow! That drill bit was walking all over the plexiglass. How can you drill an accurate hole with that bit?

[JRMakaJIMMI]

No lubricant, no painters tape, no bottom support, and too high rpm's..and stepdrill's are generally better at this...working myself on making a sidepanel for pc case with plexi. This vdo was just funny on what NOT to do. Seems like you're late for something?

[rebeccak]

Very informative... answered my question ...hard to watch when your reading from your script... it drags :o)

[arthurleroy]

Who manufactures these bits, how can I order this set of acrylic drill bits.

[ut]

good video, thanks, but plz drop the rock music intro, just ruins the video, thanks