How to control Servo motor with Arduino with and without potentiometer

Learn how to control position of Servo motor using potentiometer with Arduino. For potentiometer you can use anything value between 1kΩ to 500kΩ.

*** Purchase Arduino Start Kit ***

****** Purchase Authentic Arduino Uno from ****
**** Free Course ****

The best thank you for me is to not skipping ads and Subscribing 🔔 to my channel, and liking 👍 the video. It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊 .

*** Buy Servo Motor from ***

****** Purchase Authentic Arduino Uno from ****

Chapters of this video:
00:00 Start
02:15 Code

In this video you will learn:
-What is a servo motor
-How to connect it to Arduino
-How move it to any position
-Test the servo with different position of of 1, 10. and 30 degrees

Control Servo with push button:

Tutorial by Ahmad Shamshiri form Canada
****************************
****************************

Get other projects code and learn Arduino

**** AFFILIATE PROGRAM ****

#robojax #robojaxServo

[robojax]

Please subscribe 🛎 and thumb up 👍. Thanks. I appreciate it.

[kevinparlin]

This is exactly what I was looking for. Thank you very much.

[ariesninja]

Just Awesome. I am a beginner Arduino programmer, and this video really helped me out. THANK YOU!!!

[jpsil]

always wonderful videos and very good explained . thanks

[NefariousElasticity]

Your videos are awesome man, keep it up.

[Jonathan-rbiq]

Thanks for your good sharing.👍🏻👍🏻😊
What will happen to the white arm if the potentiometer fails? Thanks

[honzco]

it was a great video for the beginner. thank you and looking forward to watching your other amazing tutorials

[SIMPAUL]

Thank you for this excellent tutorial, very helpful and informative, Subscribed!

[michaelsappl]

Hey Hey Robojax,
i have been watching some of your videos lately to learn about arduinos. In particular I am interested in controlling servo motors with a potentiometer and have slo watched your video about it. I have already done this with the arduino libraries but only a small SG90 servo works fine. I have tried to apply the program to a SunFounder (SF3218MG) with a 270° rotation range and an even bigger Takanawa servo. This caused the error that the servo does not move over the full range of the potentiometer but reaches its maximum angle before. Do you have any ideas or hints what I could change so that it works with the whole range?
enclosed i will send you the small program that i was hoping should work with the whole range.
I hope it is not too cheeky to ask such a special question.
With best regards
Michael

[muhammadfaizan]

IT IS VERY INFORMATIVE .
THANKS SIR.
PLEASE MAKE VIDEO ON HOW TO WORK WITH VARIABLE FREQUENCY DRIVER.

[gulrukh]

thanks, nice lesson.
dr. Gul Rukh Khan
from Italy. SubsCribed great work done.

[vishalgoski]

it's very easy to understand. good job and thankyu.

[buryinggod]

Excellent tutorial. Thank you very much.

[houdadahabi]

Thanks for this vidéo
Can I just add myservo write (val) in my code to open or close a door whenever I want??

[xaris]

Hello ! how can I make a sketch to run once and stop? and how to do the reverse (this sketch) move and stop again?
thank you very much for this video was very good for me !

[akhmadfebriromadon]

I am trying to make this by using servo HS-7955TG, arduino mega 2560, and potentiometer 1KOhm. But, the horn can not move smoothly. Is there any calculation to determine potentio spec?

[abhi]

thank you for the valueable informations ....

[bsamsungsamsung]

Hi, can we stop the servo into a possition predifine?

[huzams]

hello i need a help from you, i want to fix a server motor to a governor for a generator, so from a rpm sensor through arduino to control the throttle by servo motor and maintain a rpm of 1500 in a loads

[enriquemorangarrido]

is it a problem if I connect the servomotor to the 5V supply from the Arduino? Should I use a capacitor?