Wiring Up Ethernet Plugs The Easy Way - How To Make An Ethernet Cable 2022

This video shows you how to wire Ethernet Plugs The EASY way! Cat5e and Cat6 RJ45 Pass Through Connectors. We will show all supplies and tools with all prices. If you have any questions about this video please leave them in the comments down below. Thank you for being a part of The Ultimate Tech Hub Team and if you haven't Subscribed yet please do its free. And if you like this video give a thumbs up and share it. Thanks again for watching the Ultimate Tech Hub Channel! As an Amazon Associate I earn from qualified purchases.

Or You Can support us on Patreon! 🙂 Thank you!

Product Links:

FLASH SALE!!!

Best Deals On Layer 2 Managed PoE Switches:

Best Deals On Wireless Routers:

Best Deals On Mesh Wi-Fi Networks:

Best Deals On Wireless Access Points:

Unmanaged Switches:

My Gear:

All Products in our Smart Home Network Tour:

Join this channel to get access to perks:

| Great Deals the Ultimate Tech Hub Recommends! |
Ultimate Tech Hub Merchandise:

If you want the Ultimate Tech Hub to promote your product(s) or service(s)
or you want to send us something for review or testing please email us below
to request a media kit.

0:00:00 Introduction
0:00:52 Supplies
0:01:28 Tools
0:01:55 Wiring A Cat6 Ethernet Plug

[UltimateTechHub]

If you want to learn how to wire Rj45 Cat6 or RJ45 Cat5e Connectors to an Ethernet cable then this is the video for you. Thank you for watching!

[briancowan]

WOW!, RJ45 pass through connectors, no more worrying about too much or not enough jacket. I like it!

[jdk]

Great video. I just followed it and wired up an ethernet jack no problem. The only tool that wasn't something I had was the wire stripper for Cat6, but I bought a little Milwaukee one that's spring loaded. I found I had to unscrew the blade setting to loosen it because it was cutting into the interior cables. That was probably the hardest part of the whole thing.

[kanani]

i already love this channel but cobra kai <3

[GregiiFlieger]

Well done, thanks! Good refresher or the first tim!

[wbaham]

The listed connectors state that they are for 24awg cable. The Cat6 cable listed states it is 23awg. The 23awg wire is larger than the 24awg rated connectors. Problem???

[hyder]

You don't put back cover for proper punched Cable

[ultraret]

He says to take a picture of it to make sure it wired correctly-- good ideal -- just do it before you use the crimper tool otherwise if its wrong you have to cut the connecter off and redo it. also make sure the crimper tool cuts the ends of the wires off at the same time like this one he shows. cheaper one may not and its a hassle to cut those wires flush after the fact

[bocswu]

The link for the Cat6 cable goes to a 23 guage wire and the link for the connectors is for a 24 guage wire. Shouldn't you be using the slightly thicker 23 guage connectors?

[eprohoda]

How youu doing?-enjoyed~ what a epic footage-;)

[raiderwolf]

1. Don't use pass through RJ45s (they often cause shorts)
2. Split the sheath a bit at the end of the cable.
3. Pull the string to strip the sheath to length (carefully, can cut your fingers)
NOTE: Using wire strippers may damage the jacket in your pairs
4. Cut off the split sheath and inner separator
5. Pinch each pair and untwist with a half twist of your wrists
6. Insert flathead precision screwdriver between and pull apart (will straighten your wires concurrently)
7. Using a flat surface, put your wires in order whilst holding down with your thumb
8. Trim, insert and crimp
9. Repeat steps 2 through 8 until you've done all 999 more of these bad boys‽

[SueReed-ujxp]

Can't I just buy one already prepared?

[dannyschacht]

so, do you do the same exact thing to the other end? won't that make the wires opposite? I''m new to this!

[JasonsLabVideos]

Ditch the boots :( they become hard over time and impossible to squeeze to release the connector from the port :(

[johnstone]

Question: which side is face up on the connector when you are inserting the wires?

[danger_pig]

what happens if the blue sheath is not pushed all the way inside the rj45 connector? i’ve recently had some electricians run some cables and none of them are pushed inside like that

[YewPube]

Does wiring color matter when making a single cable, as long as both ends are the same color?

[tjones]

Jeez! Enough with the background "music"! I just trying to hear what you're saying...