Honda Accord Cylinder Head Removal & Installation [STEP BY STEP]

Cylinder head gasket replacement on a Honda Accord 2.2L 2.3L. Changing out head gasket, intake, exhaust, gaskets. -YOU DO NOT NEED TO TAKE OFF THE INTAKE MANIFOLD -

LINKS TO HEAD GASKET AND INTAKE AS WELL AS TOOLS AND OTHER STUFF

Honda Accord Odyssey Prelide 2.2L F22 Head Gasket:

LINKS TO PREVIOUS VIDEOS

HONDA VEHICLES COVERED IN THIS VIDEO:

1997 1998 1999 ACURA CL
1994 1995 1996 1997 1998 1999 2000 2001 2002 HONDA ACCORD
1995 1996 1997 1998 HONDA ODYSSEY
1996 1997 1998 1999 ISUZU OASIS

More About BundysGarage:

Questions, Comments, Concerns:

Twitter:
@bundysgarage

On The Web:

Music by Randall Kent: As seen on NCIS

All Rights Reserved 2022
© Copyright 2022
Bundys Garage

DISCLAIMER - DISCLAIMER - DISCLAIMER

Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.

[kenworth]

Thanks your going to save me alit of time and money. By reusing the headbolts and not having to remove the intake manifold or injectors.

[cambodianboost]

I was under the impression honda head bolts were all torque to yield.. and studs are stretched to yield.

[justintyler]

I wish I would have seen this video first... the video you played during yours is the one I went off of. That being said, I already torque the head down and had those creaks, question is, would I be safe to loosen and remove the bolts and apply grease like you did and reuse the head gasket or would I need to replace the gasket?

[prphtz]

So many steps missing before the video even begins

[johngabana]

I got charged by a mechanic 1800, did this my self, I did use new head bolts and tourqued them down to spec, but that’s not because I don’t agree with what he did, I just like to because it’s satisfying to me

[tyronemillions]

I used the grease and a couple of my bolts still clicked so hopefully not bad

[rawnlivewithsyregreen]

So you have to replace the head or you can use the same head

[jff]

Technically you will notice if the head gasket is upside down because the sides are not the same just FYI and just to let others know, you can also use engine oils for the headbolts just to be on the safe side.

[spoorksnfoons]

The hell. That dude clean the hell out the engine. First dirty as'f then all shiny

[HazardousGanja]

Is the timing belt being messed with at all

[buildingkings]

Should you clean the pistons also if they are dirty I noticed you didn't but just asking bc wanted to know if it would hurt if I use rag and Brake cleaner to wipe top of cylinders before putting head back on

[everzamora]

What did you to the upper block deck to check if it was true and straight?

[tyronemillions]

Is there a difference between vtec and non vtec?

[RonaldRayguns]

HOW DID YOU GET THE INTAKE NUTS OFF?? I’m here trying to pull my entire intake off but how on earth did you do this without all that??

[cmoney]

Quick question i have a 98 Honda accord and i got a head gasket replacement also installed the head cylinder as well and also replaced water pump and timing belt and now i am loosing antifreeze in my radiator but i don’t see anything leaking from under the hood, also the radiator is new as well what could cause it to over heat ? Now it has been a min since i got a oil change could that be the possibility?

[stripecatflippangitnamecha]

did you have your head cylinder Machine?

[minecraftmaster]

Hey man do i have to put it on time before i remove anything ?

[xXIntoleranceXx]

I’m at the part where it’s time to loosen the head bolts with a 6 point 14MM socket and for the life of me cannot get it loose, any tips? Considering a bolt extractor socket and praying it works on removing the head bolts as I’m out of ideas and really don’t wanna junk the car.

[leonardsolis]

Remember that the timing marks on the cylinder head cam match the crank timing.

[jeremiah_swishaa]

How did the cylinders on the right and left go up? I currently just took out my head and all 4 cylinders are down