Servo Channel Forwarding (CHANNEL_FORWARDING) on Betaflight/Cleanflight.

Many noob pilots of drones have problems with connecting the single servo to a separate transmitter channel.
This video about this problem. How to connect a servo to a channel on Betaflight/Cleanflight configurator and use Channel Forwarding (CHANNEL_FORWARDING).
I use a transmitter FlySky FS-iA6 and flight controller SP Pro Racing F3 to set up.
In an earlier video, you can see how to do this via Servo Pan Tilt CAMSTAB (SERVO_TILT).
---

Некоторые пилоты новички, имеют проблемы с подключением серво к полетному контроллеру SP Pro Racing F3 в конфигураторе Betaflight/Cleanflight. Я, использовал Channel Forwarding (CHANNEL_FORWARDING) для того, чтобы управлять с помощью крутилки. В более раннем видео можно посмотреть, как это сделать через SERVO_TILT.

⚑ SUPPORT CHANNEL:
❄ WMZ: Z634219551335

⚑ ALIEXPRESS BUY:
❄ FS-iA6 FS-iA6B Receiver

❄ SP Pro Racing F3 Flight Controller Board

❄ Receiver RC832

❄ MW OSD:

❄ TTL-USB UART CH340/CH340g

⚑ BAGGOOD BUY:
FPV camera:

Props:
❄ DALPROP T5045C Cyclone

Other:
❄ Antenna Pagoda v2

⚑ Song: Jordan Schor - Cosmic (feat. Nathan Brumley)

---
Muchos pilotos noob de drones tienen problemas con la conexión del servo individual a un canal de transmisor independiente.
Este video sobre este problema. Cómo conectar un servo a un canal en el configurador de Betaflight / Cleanflight y utilizar el reenvío de canales (CHANNEL_FORWARDING).
Utilizo un transmisor FlySky FS-iA6 y el controlador de vuelo SP Pro Racing F3 para configurar.
En un vídeo anterior, puede ver cómo hacerlo a través de Servo Pan Tilt CAMSTAB (SERVO_TILT).
---
Viele noob Piloten von Drohnen haben Probleme mit dem Anschluss des einzelnen Servos an einen separaten Senderkanal.
Dieses Video über dieses Problem. So verbinden Sie ein Servo mit einem Kanal auf dem Betaflight / Cleanflight Konfigurator und verwenden Sie Channel Forwarding (CHANNEL_FORWARDING).
Ich benutze einen Sender FlySky FS-iA6 und den Flugregler SP Pro Racing F3 zum Aufbau.
In einem früheren Video kannst du sehen, wie dies über Servo Pan Tilt CAMSTAB (SERVO_TILT) geht.

[xVoLAnD]

Betaflight/Cleanflight Servo Channel Forwarding

[gorskotoprase]

голямо благодаря от доста време се мъчех да го направя

[rollieford]

Using your video, I successfully bound my servo channel to Pwm2 since its useless when running cppm. now i can have custom servo and all 6 motors

[GerusDeimon]

как я долго искал подобное видео... Спасибо!

[golovanoffpv]

У меня после включения channel _forwarding при арминге не запускаются два мотора. В чем может быть проблема? Протоколах?

[felixbaum]

I have a problem, I can't change the output in the cli, I use BEtaFlight 3.0.1! My Servo is plugged in PORT 8, PORT 1-4 are my motors!
"
$M>_tARM;AIR ANGLE MIX;CAMSTAB;$M&gteû‘$M&gtni
Entering CLI Mode, type 'exit' to return, or 'help'

# version
# BetaFlight/SPRACINGF3 3.0.1 Oct 18 2016 / 10:35:52 (48b7b4f)

# resource
IO:

A00: PPM IN
A01: FREE
A02: MOTOR7 OUT
A03: MOTOR8 OUT
A04: ADC BATTERY
A05: FREE
A06: MOTOR1 OUT
A07: MOTOR2 OUT
A08: FREE
A09: SERIAL1 UART TX
A10: SERIAL1 UART RX
A11: MOTOR3 OUT
A12: MOTOR4 OUT
A13: FREE
A14: FREE
A15: FREE
B00: MOTOR11 OUT
B01: MOTOR12 OUT
B02: FREE
B03: LED1 OUT
B04: MOTOR9 OUT
B05: MOTOR10 OUT
B06: I2C1 SCL
B07: I2C1 SDA
B08: MOTOR5 OUT
B09: MOTOR6 OUT
B10: FREE
B11: FREE
B12: FLASH CS
B13: SPI2 SCK
B14: SPI2 MISO
B15: SPI2 MOSI
C13: MPU EXTI
C14: FREE
C15: BEEPER OUT
F00: FREE
F01: FREE
F03: FREE
F04: FREE

# resource MOTOR 8 NONE
IO:

A00: PPM IN
A01: FREE
A02: MOTOR7 OUT
A03: MOTOR8 OUT
A04: ADC BATTERY
A05: FREE
A06: MOTOR1 OUT
A07: MOTOR2 OUT
A08: FREE
A09: SERIAL1 UART TX
A10: SERIAL1 UART RX
A11: MOTOR3 OUT
A12: MOTOR4 OUT
A13: FREE
A14: FREE
A15: FREE
B00: MOTOR11 OUT
B01: MOTOR12 OUT
B02: FREE
B03: LED1 OUT
B04: MOTOR9 OUT
B05: MOTOR10 OUT
B06: I2C1 SCL
B07: I2C1 SDA
B08: MOTOR5 OUT
B09: MOTOR6 OUT
B10: FREE
B11: FREE
B12: FLASH CS
B13: SPI2 SCK
B14: SPI2 MISO
B15: SPI2 MOSI
C13: MPU EXTI
C14: FREE
C15: BEEPER OUT
F00: FREE
F01: FREE
F03: FREE
F04: FREE

#
"

[foxone]

I understand everything but one, I have an omnibus f7 v2 controller. To what pin on the PCB do I have to connect the servo if it wants to use it as a load drop mechanism, controlled by a switch, or as a lighting switch. I know that you can probably use a pin for LED, but can I use, for example, pins to communicate with GPS? or some other?

[Kensin]

В видео вы сказали что на выход мотора можно сделать не управление серво, а сделать как бы два положения 0 или 1, вопрос, как это реализовать, а то у меня на выходе присутствует шим, а я хотел подключить мощьную поисковую пищалку, а при наличия шима она зудит постоянно

[classics]

Where can I find the document on Channel forwarding please? I have got my Servo working but its panning / tilting with Quadcopter movement.

[rharripersad]

can i put it on channel 7 or 8 instead? i have a hex x set up in pmw 1-6 already

[channelTMR]

А если напрямую подключить серву к приемнику будет работать, или надо обязательно через пк?

[lookinward]

How about multiple servos? I just tried using your vid as a test to do two servos but only got one working?

[zagy]

And then my quad can't arm. I'm using cppm.

[nikolaynikolaev]

подключил серву на прямую, не знаю, что я напутал но в итоге pixhawk сгорел😢

[andremedina]

every time I do this tutorial, motors 3 & 4 stop working and I have to re flash my drone

[wowiezowiepowie]

to bad you have so many ads such a waste of time