How to Configure Multi-WAN on pfSense | Step-by-Step Guide

#pfSense #MultiWAN #LoadBalancer #NetworkSecurity #TechTutorial
In this video, I'm going to show you how to configure a Multi-WAN setup on your pfSense box. If you have two ISPs and want to optimize your network with load balancing, this tutorial is for you. Follow along as we go through each step to ensure a smooth and efficient setup.

📽️ In This Video:
*Introduction to Multi-WAN: Understanding the basics and requirements.
*Network Diagram Overview: Explaining the setup and IP configurations.
*Interface Configuration: Renaming and setting up your WAN interfaces.
*Gateway Setup: Configuring and monitoring your gateways.
*Load Balancer Configuration: Creating and setting up a load balancing group.
*Firewall Rules: Establishing rules to pass traffic through the load balancer.
*Verification: Testing and verifying the Multi-WAN setup.

Amazon Affiliate Links:

These are fast-selling products through our Amazon affiliate links, check them out and help us earn a small commission when you purchase products through our links. Thank you!

HELP ME MAKE A DREAM OF 500,000 SUBSCRIBERS
📖Disclaimer: All contents provided by this channel are meant for EDUCATIONAL purposes only.

▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Follow me on social media:
☑️For business inquiries, gifts, collaborations, PR packages & sponsorship:
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Please don't forget to LIKE, SHARE, AND SUBSCRIBE. Let us Keep the love and support burning. Love you all. 😍😘

#pfsensemultiwan #pfsenseloadbalancing #torogipro

[onanadem]

Hello, I love your videos they are direct and easy to follow. I have a newbie question though maybe u can point me to the right direction. I have three ISPs with ISP-1 and ISP-2 both having 30mbps and ISP-3 with 50mbps. What I'd like to do is use ISP-1, ISP-2 and ISP-3 for general usage but with ISP-3's bandwidth toned down to 30mbps (this will be ISP-3a). The remaining ISP-3b 20mbps will be used for usage of special clients. So all in all I have virtually 4 ISP's (ISP-1, ISP-2, ISP-3a and ISP-3b) and I have 5 ip address for each actual ISP.

My questions is, Is there a way to split ISP-3's bandwith to two (30mbps and 20mbps)? Im thinking of adding a network switch between ISP-3 router and my PFs box so I can use two ip addresses and connect 2 cables to be able to use 2 ip addresses then connect to my PFs box. Do you know a better way maybe?

[old-patriot]

Thank you! Got it all setup, with your help, of course.

[philippeguarino]

Well Done !!! thank to you I was able to setup my pfsense setup

[ERolando]

Very Good .. Greetings from Paraguay/ Muy Bueno ... Saludos desde Paraguay

[geronetolentino]

thanks for this tuts, easy to follow. more tutorials to make sir. very nice tutorial

[paulkelsey]

Aftertrying and trying at least works with my pfsense <3.
Trick: If you´re not using IPv6, disable it (gateways config) and disable IPv6 rules in firewall.

[fbifido]

@6:17 - you did not test if the loadbalancing is working, you just tested if both ISP is up & can ping their monitor ip.

[pramodkumargangwar]

hi sir your videos very helpfull.
sir can you guide me that how to divide bandwidth group basis?

[muhammadaamir]

I have two WAN's ISP_A and ISP_B and just one LAN...
Both Gateways pings and connects but the system IP's under the ISP_B are not pinging?
any idea why? If the gateway ping then why not? 😔😔😔😔

[victorsasumi]

Sir i have my dell 3010 with pf i have 6 lan card installed 2isp for lan and 2 isp for lan2 lan2 for hotspota lan1 for fiber connection is it possible to balance the 4isp togeher and how then may i know how to speedtest the mb signal from pf before balansing how did you do it

[petemalou]

If i have 10 client pc do i need to install this sofware to every pc? Why not just use a load balancer router? How dofferent are the two? TIA

[michaelremedios]

Sir after you made the configuration, was the bandwidth from the two isp aggragated upon speedtest?

[jeromebasco]

Good day sir.. can i use my pc to run pfsense as loadbalancer for my 3 isp..? thanks

[horaciosilvaporras]

Tengo el FW con 2 ISP diferentes, los tengo en el balanceador de carga. También puedo configurar VPN IPSEC en cada ISP pero necesito que sean conmutables entre ellos en caso de caida de alguno de los 2 ISP. como se configura esa conmutación?

[anandsingh]

It is not load balancing rather HA configuration as Active-Passive

[AkcIT-gv]

can i use vlan to add my isp2 in my pfsense?

[lestherabong]

Sana sir sunod na video yong deny all website but one, sample gmail at google drive lang po ang ma access. Thanks po :)

[giuliolanzoni]

Hello
I followed the tutorial and I was able to immediately activate the load balancing function with 2 connections.
Looking at the results with 2 connections I thought about buying a third one but I haven't been able to configure pfSense can you help me? Thank you

[md.mudassirahmed]

Pfsense, , we need hardware or we. Can use this with usp wich is better

[johnnielacapuyan]

is it going to failback when the primary wan is up again?