Nissan P0507 Idle Control System - Idle Relearn Procedure

This Nissan Murano had a code P0507 after performing other repairs and cleaning out the throttle body. This particular code basically means that the RPM are higher then expected probably from an intake/vacuum leak or something like that.But in this case I was almost sure that it was caused because we cleaned the throttle body. so this is how you do the relearn of the idle control system.

if you want to help out the channel, just use my Amazon link when sopping at amazon.

**RE-LEARN PROCEDURE STEPS**

Idle Air, Volume Learn.
1. Make sure the accelerator pedal is fully released.
2. Turn ignition ON, do not start engine, then wait 3 seconds turn the ignition back off and wait 10 sec.. redo this procedure 3 times
3. Next, Fully depress and release the accelerator pedal 5x within 5 seconds
4. Wait 5 seconds, then fully depress and hold accelerator pedal. After Approximately 10 seconds, the Malfunction indicator light will switch from steady to blinking. Approximately 9 seconds later, the light changes from blinking to steady once again.
5. Fully release accelerator pedal and start the car within 3 seconds.
6. Allow to idle. Wait 20 seconds.


Hope it help some one out there. Don't forget to SUB!!!

If you would like to leave a donation here is a link ...

Follow me on INSTAGRAM

Twitter.

Facebooks Hobbies

My Gaming Channel.

The information presented in this program is based on a specific diagnostic case and might not directly apply to the vehicle you are repairing. We do not represent or warrant that the information presented is complete or error free. Please take all safety precautions. We disclaim any and all liability for losses, injuries or damages in connection with your repair."

[FalconsGarage]

if you want to help out the channel, just use my Amazone link when sopping at amazon.

[rapidtransit]

You guys save people money that don't have it. Taking a car to the dealer is very expensive. They charge 100 dollars just to put it on a scanner. Thanks a lot for helping people .

[CharleneDixon-kwmn]

Thank you very much, your video really helped me. I'm a single mother and I follow your instructions of what you said and it works. Thank you❤

[Kielohawk]

If this isn't working for you and you still have a high idle and check engine light, do all 3 procedures with the engine fully cold! It worked on my 06 Nissan Pathfinder. I cleaned my TB and my truck started idling around 1K and check engine light. Tried this procedure about 20 times with engine and transmission fully warm and it did not work. Next day, I thought I would try it with engine fully cold with nothing to lose and BAM, 625 RPM after a few minutes of warming up. Good luck!

[frank]

Hi Falcon. I Can not Thank You I have 2007 nissan sentra 2.0 engine car ran terrible i cleaned the throttle body and the hose to it was cracked i replaced it. After cleaning throttle body ran better but the idle was high and surging while driving . Well thanks to You i Followed your Procedure it worked on the First try i am totally Amazed my car runs PERFECTLY . Again Thank Frank

[sheeshalready]

I tried this method on an 07 Altima several times, did not work. I finally hooked up my ThinkDiag in hopes that it would have the ability to do the relearn, and it did. Fixed it perfectly. We appreciate videos like this, thank you.

[Guts]

This fixed my hard start issues on my Sentra 2005. Thank you!

[dfields]

This is great
It’s the Hitachi relearn procedure
Apparently hitachi makes this component for Nissan I think.

[sithet]

Went through the instructions, didn't get the flashing indication, but it cleared none the less. Thx for the vid!

[Kencan]

Worked great on my Nissan350Z! Thanks a lot bro! Worked on the first try too! After I had my CamSensor Bank replaced, my car was idling around 1500 rpm! Now I’m down to a solid 500rpm!

[bradm]

Thanks, it worked great!. I did clean my throttle body and my RPM increased. I thought that was normal till I got that P code. You video helped me work that out.

[jeremyolsen]

I totally botched the process. BUT IT STILL WORKED! 2002 Nissan Sentra. Thank you so much.

[kaleidoscope]

I have 2006 Nissan Altima and just bought it used (it is July 2018). I bought it off my nephew's used car lot - they just got it as a trade in. My symptoms are: I usually get steady idle at 1000 rpms in Park or Neutral. Occasionally, I get steady idle at 1500rpms. But abt every 8th engine startup it'll immediately dip once to abt 600rpm and steadily climbs to 2000rpms where it will start a cycle of dropping & surging between 1000 and 2000rpms. It stops the surging & high idle as soon as i put it into gear (drive or reverse). It will not do it on next few cranks. It'll take about 6 or 8 cranks to hit it again.
My MIL is P0507.

The dealership changed an engine mount the day before it started happening. At first my nephew thought the mechanic might've left something unhooked or knocked something loose pulling off the cover to get to the engine.

Is this a potential? What all should i check? Do you have a video that covers every point of failure in this system? Thanks

[allenrachal]

you saved my car. light went off after doing this procedure 5 times in a row.

[SirAJentz]

Worked on a 2015 nissan pathfinder 3.5l, thanks.

[AEFarnam]

Dude omg....tried this last night like 40 times with another dudes video, could not fucking get it... Literally 1 try with your video, SUCCESS!!! Thank you my brother, you really really helped me out today!!!

[RicardoMartinez-krqk]

This one worked for me, 04 altima, after trying multiple versions found on YouTube and the forums, including those claiming to be "from the factory". This one was found by my beautiful, voluptuous, curvy, sexy wife, so credit goes to her for finding this video.

[nasnismo]

Works for my nissan latio/tiida/versa 2006. Thank u.

[ablake]

Just sorted my elgrand that was idling at 1200rpm thanks

[Scottii]

I have a push to start how do I make this work