Nissan Hardbody Dies at Idle (FIXED)

[westernwill]

Game is Operation. Thanks for the video. After driving for 30 min at freeway speed my 97 D21 decided it should idle around 3-4k.

[conradescue]

The game was called: Operation. I think by Milton Bradley.

[mikeycurtis]

Instead of cutting wires: use a pick or tiny flathead on the front of the connector (where the plug meets the other plug), on each pin there's a springy piece of plastic inside the connector.. get ur tool between the plastic spring and the actual pin (terminal connector)... Now while prying them away from each other, u have to also pull lightly on the wire. It's literally the EXACT same concept as releasing a zip tie, instead of cutting one. I mean, so exactly the same, that this plastic spring thing I'm talking about, looks identical to a zip tie.

[JoelDanner-fh]

And high temperature tack would be good for holding gasket in place good for putting it on

[KodyAllenEstep]

Longest 8 minute video I’ve ever watched, but good stuff. Keep it up 👍🏽

[bernardaleman]

great video... thank you... my 95 Hardbody doing the exact same... tried a lot o stuff ... replacing ICV today! fingers crossed!

[WizardOfWhoopee]

Near the end it surged and you said you 'put the old airflow sensor back on'. The new China one was bad? My '95, 2.4 auto, runs fine but idles so rough the whole truck vibrates. I'm suspecting this iac also.

[davidbryant]

Mine won’t even think to idle .. got change the manifold gasket’s today sounds like a drag car. Just bought it think the guy got me

[oxy]

Hey what’s up, I got a 1993 nissan with a a fuel problem, the pump pumps the gas through all the way through the filter and into the injector rail, but it’s not going into the carb, it runs when I put gas in the top of the carb but it turns off once the gas runs out, It looks like It has the same amount of pressure as my other truck which is the same just 1 year older. I tried everything except the replacing the fuel pump.

[BoostedPastime]

Due to the engine moving in the bay from side ro side it looks like you need new engine mounts.

[jorgemunoz]

For the wires on the valve how did you know which one goes on what side or didn’t not matter?

[guanajito]

I have a 95 hardbody clutch was just replaced... manual all gear work 1 thru 5 but not the reverse

[Kingwara_SA]

I wish u had first bought cab cleaner n spray the idler air valve then airmass flow cleaner for idle sensor

[matthewmurdock]

My 95 Nissan is doing that right now as well replaces maf sensor it didn’t fix it so now idle control valve but it’s $130 or so at o rilyes and i don’t wanna ruin it so will have my dads friend help me thank you for video been wondering if fuel pump was bad but it’s always primes on.

[terribleart]

Thank you for the video! By chance do you remember the brand of Mass Airflow Sensor you used? I keep reading only to use OEM but am curios if you used OEM and if not, did the replacement you used work okay? Thank you again for the video!

[soloone]

Where do the wires go they are both black

[MrMister]

Ugh I'll just have my mechanic do it lol

[carlosorozco]

Question
I still have problems with my 1993 Nissan when I had the old sensor it sucked air through the small hole where the MAF breathes I covered it with my finger and the truck turned off by itself now I put a new one from autozone and when I put my finger it doesn't do anything and when I run It won't let me run more than 1500 revolutions, it jerks, could it be that the sensor doesn't work?

[giolopez]

Do you have a link for the IAC replacement part you used?

[ThePunkasfuck]

Do you have any updated video of driving that proves this actually worked? Rather than a startup showing running or a couple of seconds….