How To Replace Front Wheel Bearing 2007-Present Toyota Tundra

Buy Now!

Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision. This video shows you how to install a new wheel hub and bearing on your 2007-Present Toyota Tundra.

This process should be similar on the following vehicles:
2007 Toyota Tundra
2008 Toyota Tundra
2009 Toyota Tundra
2010 Toyota Tundra
2011 Toyota Tundra
2012 Toyota Tundra
2013 Toyota Tundra
2014 Toyota Tundra
2015 Toyota Tundra
2016 Toyota Tundra
2017 Toyota Tundra
2018 Toyota Tundra
2019 Toyota Tundra
2020 Toyota Tundra
2021 Toyota Tundra

Tools you will need:
• Pocket Screwdriver
• Straight Cutters
• Socket Driver
• Copper Anti-Seize
• Liquid Thread Locker
• Rust Penetrant
• Wheel Chocks

Check out our playlist:

⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[TRQ]

√ *Watch the Video*
√ *Do it Yourself*
√ *Save Money*

[danielfrain]

Thank you for showing that vid without an added 20 min of “story line”. I appreciate getting what I need to see without spending 30 min to an hour of unnecessary extra fluff

[yugster]

One of the best get right to it videos. No talking about ur dog or chit chat straight to the job. Just the way we like it.

[jasonlopez]

Probably one of the best how to videos I've ever seen.

[EmmAitch]

Awesome video! Replaced my wheel bearing with relative ease!

[jeffgrig]

thanks for these videos. Also, I life that the vehicles are not brand new and that youre working on real condition vehicles. Gives me encouragement that i can work on my midwestern truck

[donjuan]

Good thing you put what was left of that backing plate back on

[miztrusa]

Great video TY.... Gonna be doin that to my 07 too but I'm not putting that rusty, crappy rear dust shield back on cuz o new one isn't that much. As a side note I'd put another lug nut on for that pry bar.... 😁

[JohnCoats]

What size socket for the 12 pt axle nut? Thanks!

[thomasjohnson]

Don't forget to buy extra wheel seals too. There is a very high chance yours will be damaged in shipping cause I've never met a ups driver that's gentle with a 40 lb box and apparently Trusted Reliable Quality stops at packaging.

[thejohnboatfaithfishingand]

I see Toyota got smart and used the same design as newer Forerunners. Much easier to replace the bearing/hub as an assembly than to fight with pressing the bearing in and out of the knuckle like you have to do on the 1st gen Tundra.

[davemina]

what thread size is the bolt used to push the rotor off ???

[robbergeron]

When I bought my hub assembly, it came with a new seal AND a round O ring. Where does that go?

[ivans]

I hope I'm wrong but aren't those rotors directional and doesn't that belong in the driver side?

[taylorsutliff]

Are these TRQ wheel bearings good….how long do they last I have a 2014 tundra

[joewong]

Nice instructive video but I was surprised you didn’t replace the dust shield which would’ve cost
$20 -30.00 more.

[tosemcriatividade]

Dumb question here: does this applies to the 08 to 2022 Sequoia?

[rickyzechariah]

What is the thread size of the bolt that goes into the rotar to push it off the wheel? The one at 1' 49"?

[benjamindaniel]

My rear seals were smashed in the box.
Mine also had an o ring to install on the back side of the bearing.

[brucemacdonald]

I would have replaced that backer plate when you had it all apart?