MAP Sensor Cleaning

Removing and cleaning the MAP (manifold absolute pressure) sensor on a 2001 to 2008 Peugeot 307 1.4 litre petrol. Thanks for watching. Please comment, like and subscribe !.

~~~~ Part Links ~~~~
As an Amazon Associate I earn from qualifying purchases.

All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.

Read important information below:

Disclaimer:

Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Screwsnutsandbolts recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.

[screwsnutsandbolts]

Thanks for watching my video. If you found this or any of my other videos helpful, maybe you could consider supporting my channel by using the ‘♡ Thanks’ button below each of my videos. Your support would be greatly appreciated, thank you ! 👍

Screwsnutsandbolts

[smartweartech]

great vid, short and explicit, not talking for half hour.

[joannaatkins]

Wow, a simple, easy, practical video with no buggering about. THANK YOU.

[eyesofthetiger]

Very straightforward explanation. I enjoyed watching it.
Many thanks for sharing.

[ranjeetbhoirekar]

It is always good to remove negative terminal of battery before removing any sensor. It avoids any potential damage to sensor. I am sure, you must have done it, but should have been shown in video.

[realfaithlife]

This video was clean and straightforward...how it should be done. Much appreciated and super helpful. S/O from Richmond, VA.

[Grenadieros]

At 2:43 i think a little bit of contact cleaner spray would help.

[TheLaxBroseph]

Thanks for posting, have to do this soon

[miguelpaolino]

A suitable MAP sensor cleaner is any contact cleaner that leaves no residue after drying, which AFAIK is all of them. Do not spend your money using a MAF sensor cleaner in a MAP, that is for a completely different type of sensor. If in doubt think about where the MAP sensor is placed vs the MAF sensor. MAP sensors are always exposed to engine oil, hence resistant to petroleum based solvents. MAF sensors are placed before the throttle body where almost no oil recirculation should reach it.

[codylujan]

I've been reading your comments about rough idle. you could also try cleaning / replacing your mass airflow sensor. Ignition coils go after some time too. not always spark plugs.

[darrenangel]

Great informative video well made sir.

[nunograca]

Hello thank you for vídeo, did you notice any difference on the performance or consumption of the car after cleaning the MAP sensor
Thank you

[CorvusDraconem]

Need to do this on my 05' ford escape my engine light is on because of this someone said i can clean it with brake fluid but I'd rather use a maf cleaner like you did thanks

[halloweenjunkie]

I cleaned my map sensor and the check engine came on a few minutes later after running the car. It only goes off once I get the car moving at a certain speed...amazon does have the part GM for $48 which is awesome ☆

[vlatter]

Is Throttle Body & Air Intake Cleaner a suitable alternative?

[ejer.]

Man, why did not you use a car scanner. It would be easier. My car had the same prb like yours. I pit new spark plug, throttle body and celan MAP and MAF. After scanner, the problem was coil.

[Scorpion_heart]

Does the sensor have to be one-way? Because it is a broken sensor and its direction is variable.

[javiercetina]

I noticed you used MAF sensor cleaner to clean the MAP sensor! Is this OK, because I cleaned my MAP sensor with MAF sensor cleaner, using the exact same brand that’s in the picture of your video, and now my check engine light is on.

[wooddee]

can i use Mass air flow Cleaner by CRC spray to clean it?

[mr.markov]

I have a 308 / 2010 and stupidly I can´t locate the map sensor. It´s not on the same spot as it is in this 307. Where should I look?