3d Printer Bed levelling Method for beginners and pros (Quick and easy)

Are you struggling to get a good first layer? This can be the first problem beginners come across. There are many tutorials for how to level your bed. Many of them leave you with more adjustments still to do afterwards. This simple method will give you a near perfect first layer within minutes on any 3d printer.

...............................................................................................................................................................

BUY ME A COFFEE
...............................................................................................................................................................

Affiliate links (If you purchase something after clicking any of the below links I may earn a small commission at no cost to you. This is a great way to support the channel)

Feeler gauges

Ender 3 v2 3d Printer
Amazon

Banggood

[gfdggdfgdgf]

This is definitely the best leveling video, not leaving out any steps, no shouting, no loud music. After messing around for hours this video got me printing without any errors.

[digitaltown]

What a great video. Easy to follow and the 0.1mm Z setting made all the difference. As soon as the next print started it just looked right and came off the bed at the end with the correct amount of pressure. Many thanks.

[larryfroot]

My go to bed levelling guide. I have it pretty much stored in my head, but I rarely have to level the bed so it's good to have a reminder that, yes Larry, it is like this!

[firestop]

Hi Ricky I rewatched your video about the 0.1mm Z setting and it made sense the second time I watched it. It was a great video tutorial.

[LancerShifty]

I was struggling so bad until I watched this video, thank you so much!

[DocBlasto]

Following up-- Wow! I just calibrated my e-steps and cleaned and adjusted the bed as-per your videos, and I'm currently printing the best first-layer I've seen since almost four years ago when my printer was new. Thanks again!

[DocBlasto]

This is the best bed-tramming video I've seen yet. It's the only one I've watched that even mentions spring tension prior to the adjustment and resetting the limit switch position, or that mentions the thickness of your feeler gauge and raising the nozzle height by that amount. Excellent.

[MallocArray]

This makes much more sense than other guides I've found, which have you tram the bed cold and just hope that it thermally expands by 0.1 mm. I happened to have feeler gauges from a tool kit, but intentionally raising it by a known distance, leveling to that, and then letting it go back to 0.0 is way more intuitive.

[ShoKurvz]

You deserve way more followers! You explained everything perfectly, with the knowledge to back it up. Thank you 🙏

[TOMA]

Excellent explanation, very calm straight to the point and easy to follow.

[chrismclain]

This is by far the most helpful video on bed tramming. This had me up and running in no time after days of frustration. Thanks for the step by step instructions. Made a world of difference.

[andrewkloiber]

Oh man, this is so so exciting!! Thank you for sharing this, I can't wait to try this!

[mtsurikov]

Super-useful and easy to understand. I would've never figured this out with just the instructions supplied with the Ender 3 V2. Thank you very much.

[Necro_]

I have to thank you so much. If it wasn’t for this video I honestly think I would have not use my 3d printer as much as do now.

[civicsrcool]

I have had an ended 3 v2 sitting in my room for years unused because of how hard it was to level the bed on initial setup… this video helped me much! Thank you!

[TOmlltimes]

Thank you so much! This worked out really well and my prints are looking great! Very easy and made lots of sense. You gained my subscription.

[theswan]

Can't recommend this enough, did everything in the video and it took me all of 5 minutes to get a decent level print bed. the instructions were clear and I had no trouble following them. thanks! :)

[StonesAndBones]

Thanks a lot for this video ! I wasn't able to level this bed and couldn't get why. Now I know, and everything is printing great !

[striveupward]

Excellent tips. Thank you. The pace was a bit fast to absorb, and I had to "rewind" many times to get the key points. I really appreciate the help. Blessings.

[TheSupertecnology]

This is by far the best tramming video I've seen. So much so, that I believe Profesional Firmware's auto tramming not only follows the same logic (albeit automated), but gives exactly the same results: a nozzle that barely touches the bed when set to 0mm height.