How to change a car battery without loosing memory in MODERN CARS!!!

This video will show you how to replace and change a car battery in modern cars! how long does it take to replace a car battery? In this video we will show you how to quickly, easily and safely replace your car battery.

Here are a few reminders when replacing or changing a car battery especially for modern cars

Negative cable first for removal

Positive first for installation

Always keep horizontal

Make sure to use a Memory saver

***********
***********

[bluelemonade]

Hands down. One of the best videos out there that shows clear steps and showing safety steps properly

[markramsey]

When using a memory saver the positive cable stays hot, put a rubber glove over it so it doesn't ground out.

[asianstud]

Wish i found this video soon. Too late . My engine was violently shaking after swapping out my battery. Lost all presets and memory of how my car was supposed to run. Well now I know.

[ayoCanada]

I'm about to change my battery, it's very important that I have to watch this carefully

[tommyd]

I don’t have a small power source, can I connect the positive and negative cables to another cars battery ??

[leoseries]

I used the same method but I only needed a 9v dry battery to maintain the memory whilst I swopped the car battery. I made sure that all lights including the courtesy (door open) light was off and that the infotainment system was off. It worked fine.

[richardstoehr]

It was a good video on how to save your presets my question would be why would someone put a new battery in and not clean the cables?

[THEFIRE]

I've replaced batteries in a 05 lexus, 15 sienna, and a 16 Altima. Never used the memory saver and they still had all their memory.

[dhowar]

I have a 2007 Toyota Sienna and have changed the battery without a memory saver and haven't lost memory. What year cars did the memory loss start?

[flymoracer]

there's an additional step that might be necessary. The battery monitoring system will need to be reset, coding the new battery to the car, allowing the charging strategy to be adjusted for the new battery. You'll need a suitable diagnostics scan tool for this, or might need to pop into a garage or dealer that has this equipment. The car will likely run just fine on the new battery, but an incorrect charging strategy could reduce the lifetime of the battery.

[gabbytanner]

Thank you so much, you made it clear and easy to understand

[Okinanam]

Just use an extra fully-charged battery on the side to power using a jumper cable.

[SuperFredAZ]

Should you have wiped a little grease on the battery terminals after installing?

[jaygre]

Showing a 12 V accessory to plug in your computer saver, is OK if you have one. It would have been better if you would have also shown how to connect if you don't have the peripheral equipment.

[sorinsorin]

What happens if you lose your settings? How can you restore them? The guys at the shop changed my battery and didn't do any of these. Now i have none of my settings even if they are checked in my car settings menu

[westonlee]

Could a external power supply be connected to the battery terminals during the battery replacement as an alternative to a OBDII memory saver? I'm thinking if I keep power on the terminals then the objective would be the same. thank you

[goddessmanbo]

102.3 you must be in Florida thank you for this video

[jshjho]

Can be done with a car charger or using a pair of jump leads.
This is a better and cool idea
and it works.
TBH
HOW many people is going to be changing the f.. ing battery more than twice in its lifetime
Let alone buy this memory saver shit

[mistervacation]

I'm positive about the negative, but a little negative about the positive.

[hotsauce]

Why can't you just use the jump starter cable and connect them to the car battery terminal, like a wire or something and then remove the battery while the car is still actually connected to a power source. Then when you reconnect the car battery terminal with the car battery, you can remove the wire and disconnect the jumping cable.