filmov
tv
Strain Gage Installation Tutorial (350/5000 Ohm) - Part Two (Soldering)
Показать описание
Learn how to solder correctly from Ben and Darryl, our stress analysts.
In this iLearn, Ben and Darryl demonstrate the best gear and techniques, and provides helpful tips on properly soldering to any Advanced Sensors Technology strain gage (from 120 Ohm to 5000 ohm).
We start from the beginning with type of tools, wires, solder and flux you should use and how to prepare the wires for a strong soldered joint.
All the recommended procedures and materials needed for attaching leadwires to a Micro-Measurements C5K strain gage (Advanced Sensors Technology) are covered in this video. Although soldering is basically a simple procedure, the experience-proven methods featured in this video result in reliable strain gage sensor installations based on the use of Micro-Measurements strain gages and installation accessories.
Micro-Measurements offers a comprehensive selection of stress analysis accessories:
In this iLearn, Ben and Darryl demonstrate the best gear and techniques, and provides helpful tips on properly soldering to any Advanced Sensors Technology strain gage (from 120 Ohm to 5000 ohm).
We start from the beginning with type of tools, wires, solder and flux you should use and how to prepare the wires for a strong soldered joint.
All the recommended procedures and materials needed for attaching leadwires to a Micro-Measurements C5K strain gage (Advanced Sensors Technology) are covered in this video. Although soldering is basically a simple procedure, the experience-proven methods featured in this video result in reliable strain gage sensor installations based on the use of Micro-Measurements strain gages and installation accessories.
Micro-Measurements offers a comprehensive selection of stress analysis accessories:
0:23:40
Strain Gage Installation Tutorial (350/5000 Ohm) - Part One.
0:20:27
Strain Gage Installation Tutorial (350/5000 Ohm) - Part Two (Soldering)
0:11:02
Tutorial: Strain Gage Install on Composite Materials
0:06:08
Tutorial: WK- Series Strain Gage Installation Using M-Bond 610 Adhesive
0:10:44
Tutorial: How to Trim and Solder Wires Prior to Installation of a Strain Gage
0:01:27
Soldering a CEA Strain Gage (Training Video) – Advanced Sensors Technology.
0:01:30
Strain Gage Installations with M-Coat B.
0:05:58
How to attach the strain gauge and wiring
0:13:14
Weldable Strain Gage Installation.
0:05:00
ITM Strain Gauge Install - M-Bond AE-10 Epoxy
0:16:05
DOES STRAIN GAGE RESISTANCE MATTER?
0:55:22
Strain Gauge Installation – Tips & Tricks (60 Minutes)
0:01:37
Strain Gage Soldering Tutorial
0:01:34
Strain Gage Installations with M-Coat A.
0:07:59
5KΩ Foil Resistor Meets a 5000 ohm Strain Gage Sensor. (Foil Technology Products)
0:02:31
Bridge Completion Modules – Built with Vishay Foil Technology (5000 ohm)
0:02:22
Strain Gauge Testing on a Desert Island
0:04:21
For those who hate to solder - New strain gage sensors with pre-attached leads.
0:05:26
How to Select a Strain Gage – Gage Length.
0:02:20
How to Select a Strain Gage – What Is The Right Resistance To Use?
0:06:20
Basic Data Acquisition Software Using 5KΩ Sensor. (Part Two)
0:02:54
Electronics: 4-Wire Strain Gauge Measurement
0:00:45
Can you guess the stress in a 1- ohm resistance change? #sensors #electronic #diy #engineering
0:02:44
STICKY STUFF! Why Proper Strain Gage Adhesive is Important
Комментарии