How to Build a DIY Backyard Swing Set

Learn how to build a DIY backyard swing set. In this video, I will detail the entire process to build a DIY backyard swing set. I built this entire swing set for only 285.00 dollars which includes all lumber, hardware, and accessories such as the swings and playset anchors. This wooden swing set is built with an A-frame design. I will explain all the materials you will need to build this A-frame swing set as well as provided all of the building instructions. This wooden swing set is 12' long and can house three swings of various kinds.

Caution:
For demonstration purposes. Actual structural integrity must be determined by the Individual builder(s). The suggested weight limit for the safest operation of this type of swingset is around 300 lbs.

#swingset #DIYswing #backyardswingset

Material List: Rough Cost 285.00
- Pressure Treated Pine Lumber
x4 - 4"x4"x10'
x1 - 4"x6"x12'
x4 - 2"x4"x8'
- Exterior Grade Hardware:
x20 - 4" Lag Screws
x28 - 2½" or 3" Deck Screws
x6 - Swing Hangers
- Swing Set Accessories
x3 - 66" Plastic Coated Swings
x4 - Playset Anchors
x6 - Locking Carabineers

I have many more woodworking videos on my channel so don't forget to swing over to the Shopfix channel page to check more videos out! If you enjoyed this DIY woodworking video don't forget to smash that like button! If you want more DIY woodworking videos feel free to subscribe to the Shopfix channel, thanks so much!


Want to join the Shopfix Community and recieve updates on future projects? I'll be posting new Shopfix uploads and, of course, woodworking plans, Tips, Tricks and how to woodworking tutorials for your next DIY project.

Shopfix, for the love of woodworking!

[mrscorpioify]

At the 8:18 time mark when 4" is measured at the bottom of the 4×6 for the 5 degree mark. The top measurement of the board is 4 1/2" if you don't have an angle measuring tool. You make the two marks, line them up with a straight edge and you will have your 5 degree mark. I had to figure this out with a lot of trial and error. I'm almost finished with this project. Thank you for posting.

[skipmcgripcunningham]

Thank you for the comprehensive video! My husband and I built this swing set for our kids today using this as our guide and it turned out great! God bless!

[amantedelmondo]

Thank you for this video. It actually reminded me how unskilled and unwilling I am to take on a project like this. Perhaps you can make a series for absolute beginners showing stuff like what tools or machines will someone need to get into woodworking, safety measures, where and how to get the best wood for a specific project. Baby steps essentially...

[StephanLeming]

Good job what I really appreciate with your video is that you're showing people to pre drill the holes so you don't split the wood.

[mariosainezortiz]

Thank you very much for sharing all your knowledge in such detail. Greetings from the beautiful city of Morelia, Mich.

[haroldped]

Great design and instruction. The few things I did differently . . . 5/16" Spax Power lags for both the main beams and 2 x 4s (3" for the latter) . . . router all lumber before assembly to protect those little fingers . . . I was able to hoist this up alone (I am in my 60s) without too much sweat using a 6' and 8' ladder.

[bingos]

I actually watched this video believing I could accomplish this...but I just learned that I am woefully under-skilled. But this is the exact design I want.

[ChickenScissors]

Thank you so much for this video! I've watched a bunch, but this design in particular is finally, exactly what I was looking for. Looks good and gets the job done without having to do anything too fancy

[d.taylsmusic]

Building Instructions For DIY Frame:

1. Cut 60 degree angle on all (4) 4x4 posts
-Use template piece so all match
-Do not cut to point, leave a small amount flat at top

2. Mark at 10’ from top of that cut, make a 30 degree angle cut at bottom
-This one can be to a point
-Use template piece so all match

3. Use scrape 2x4’s to lift frame off ground for ease of work
-Lay down 4x6 as a reference of width 4x4’s should be apart
-Make 2 60 degree angles level at top
-Use temp blocks nailed to side to help attach clamp while you screw in side braces

4. Attach 2x4 brace 4’ up from bottom
-Screw down
-Saw off excess

5. Use excess from bottom brace at top
-Measure 5/8 from base of 60 degree cut
-Screw in

6. Remove clamps/temp blocks at top

7. Lean A Frame onto something so you pre drill some pilot holes
-Mark Lines at 2” and 4” From Top Frame
-Pre Drill with 1/2” bit, go 1/2” deep (use tape on your drill bit as reference if needed)
-Inside that pilot, do another pilot with a 1/8 bit

8. Pre-set lags into 4x4, prep it of fastening to the 4x6 once leaned up
-Draw a 5 degree angle on 4x6 each side 4” in (make long side at top)
-This creates a small angle for a frames to brace outward

9. Lean up a frame and insert 4x6 into gap
-Secure A frames to 4x6 at 5 degree angle line

10. Measure 2’ Down from top of 2x4 for next cross support
-Install angle brace from that cross beam up to the 4x6 to help with side to side sway

11. Swing Hangers Should be 20” apart and 18” from 1 swing to another

[Jazbo]

Very great job and ty for the exact directions
You’re a wonderful wood worker

[bacardi]

Thanks mate :-) made a brilliant swings and slide thingy, for my kids. Super solid, just couldn't find a 6x4 in uk! Used 4x4, and will install some type of reinforcement

[iddybiddy]

I love the design. Well done! Is the 4x6"sufficient to span that +/- 12' without deflection?

Also why did you drop that 2x4" ledger 5/8" below the 60degree cut? Wouldnt that cause the beam to sit lower than the edge of the 60degree cut and leave you with the top of the 4x4 proud of the beam?

Thanks for your good work!

Adam

[yuschampion]

Great work we just made one also, it's so satisfying rather then buying one

[vincekp]

Nice video. Would you mind telling me how tall the swing beam ends up being when you use the 10 ft 4x4 legs? Seems pretty tall in the video. Also, what’s the total area footprint foe this?

[alyssagreenler]

Hi! Looking forward to building this. Can you tell me why the 1/2 inch tip off the 60 degree angle on 4x4s? Is this just so it doesn't look strange when all assembled? Or is there another reason? Thank you!!

[Delphisteve]

I believe that those Spax screws are rated for interior...

[jaredtoles]

Did you use pressure treated wood? If so, how long did you wait to sand and stain the wood? I read that the wood has to dry first.

[faiz]

Great video! Do you have info/video on how to implement proper ground anchoring?

[algernon]

Are the angle braces made from 2x4 or 2x6? Any hints on how to make those cuts.

[mrscorpioify]

Is it still a 60 degree angle leaving that half inch piece on at the top?