One Shot Zero - ATN ThOR 4 Manual - How To Guide

preview_player
Показать описание
#ATN #HowTo guide for the #ThOR4 Manual. This guide takes you through the One Shot Zero feature for the #SMARTHD ThOR 4.

Рекомендации по теме
Комментарии
Автор

The model of scope used appears to be the 640 - 2.5 to 25 power. What is the actual target size? Size matters! when zeroing and choosing a model. Keep in mind Magnification after ~50% is digital enhancement. Note: 10x is max for this scope. DO NOT ZOOM prior to starting your zero as the scope will be off at longer distances. Follow this video and all good.

liveworkplayvans
Автор

How large does my foil target at 50 yards need to be? I put a 3" square foil tape and can't even see it.
So far this scope is getting returned because you can't see anything through it.

WilliamMcNett
Автор

Is there a way to sight it in during daylight ? Have been through a box of shells at 50 yards, then 30 yards, and tried the shot correction ! Still way off target ! Far from one shot zero !

alboeckco
Автор

Is there a way/shortcut to simply restore factory settings on my zero ONLY? Thanks.

toddjenest
Автор

How far were you from the target? I already went through a whole box of bullets and still haven't been able to sight it in correctly. When I take a shot I can't see where it hit so how can I align it?

carlosgarza
Автор

Very poor audio. It sounds muffled. Please redo this video and use a better microphone and/or enunciate your words. You could have also actually taken that second shot to "fine tune" the one shot zero while zoomed-in.

dextralsword
Автор

Can you tell me what I need to do to send the video signal to a TV monitor. Also how are you recording the carousel footage. Thanks

aajr
Автор

while trying to zero target at 50 and 100 yards, it was very pixelated and fuzzy, I could not see hit on target, how can I clean this up? and get shot on target?(I used target with handwarmers supplied by ATNco)

crav_under_the_stairs
Автор

The worst and most unsuccessful sights. I bought two sights from them, the first one is still not working, and the second one is the third time I send it to the company, I still don’t know if it will work or not.

geghamvasilyan
Автор

So im a little confused, does it sight it in for whatever range?? Because I dont get how doing that will sight it in for both 100 yds to 600 yds

Keller
Автор

Could you tell me what range you zeroed at, as I tried to zero mine at 50 yards and I could not see the shot through the scope.

micknelson
Автор

I cannot set my compass. Stuck at N (north) and despite I rotate it, or even reset factory settings still showing either ERR (error) or N. If whoever knows how to fix it please advise. TIA

TomaszDobrucki
Автор

How to adjust the x axis increments by one during zeroing? My Thor 4 get every clicks moves by 4 increments

sajuchacko
Автор

How about a link to pair your phone for naming profiles?

lesschattermoresplatter
Автор

How far do I set the target out to zero my scope?

brandonrost
Автор

After updating my thor 4 the reticle that move at the process is the white not the red one. This is ok?

federicofernandez
Автор

Can you mumble a bit a lower? Maybe slur a bit too.
Bought one of the ATN night vision scopes, what a nightmare. Tiny crosshairs, trying to get the damn thing to the location to shoot to find where it hits was atrocious.
Take that scope out like real people to a public range in bright daylight, and try to zero that garbage at 100 yards.
Collecting dust on the shelf now.

jsecure
Автор

Do any of you all have this scope already? Before I buy it? What do you think of it? Is it all you expected? More/Less? Accurate?

peterfasojr
Автор

Do you need to zero every time you turn the scope off and on or does it save the zero?

wallykozak
Автор

After I zeroed my scope, my reticle stays in the location that I moved it to (example, left 3 and down 4) How do I get my reticle to center again?

eag-qfvo