How to Cut and Install Bullnose Corner Bead Bullnose trim pices

Показать описание

Bullnose corner bead can be tricky without the tool to cut it.

Disclaimer: Due to factors beyond the control of The Drywall Doctor, we cannot guarantee against improper use or unauthorized modifications of this information. The Drywall Doctor assumes no liability for property damage or injury incurred as a result of any of the information contained in these videos. Use this information at your own risk. The Drywall Doctor recommends safe practices when working with tools seen or implied in our video and written content. Due to factors beyond the control of The Drywall Doctor, no information contained on this YouTube channel, Facebook page, website and Twitter page shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this content is the sole responsibility of the user and not The Drywall Doctor

***Like our stuff? Here's small and big ways to show support***
(We also love comments, "thumbs up" and shares :-)

Join our CROWD FUNDING effort on Patreon

*If you do this right (or even if you do it wrong too), please feel free to share! This is a community so your experiences only make this place a better resource for those who want to do their best drywall work!

Proverbs 22:29 NIV Do you see someone skilled in their work? They will serve before kings; they will not serve before officials of low rank.

Рекомендации по теме

Комментарии

I like your style. It’s like being taught by a friend in the field. I like that you don’t play music at the beginning, you stay on the subject and are clear and concise. Thank you!

boomcity

Yes they do make that specific corner ball I used to get them all the time when I was hanging drywall down south

christopherbanks

Man, life saver tip about cutting the drywall back 1/2 from the corner. I'm putting this on an inset shelf, so cutting back the wood of the shelf would be a lot more of a chore than the drywall ;-)

shaunthomas-arnold

They make bullnose (rounded) corners for wood/mdf baseboard here in use those on bullnose tight right around we glue bullnose corners to butt cuts on both sides

kirkdunn

Hey Doc here where iam at all we do is bullnose (trim tex vinyl bullnose)and the only time we use corner bead is for commercial jobs or maybe in some remodels ...we make these cleaners out of caulking tubes to clean the bullnose of joint compound...if we use corner bead I prefer the metal kind because it stays straight unlike the plastic corner bead that sometimes is difficult to sit right...either way they both look nice when done right huh

danielbalboa

I got to where I didn't need the pattern. Just cut the first piece without the perfect curve then I got to where I could eyeball the piece that butted to it. Like coping trim. Got real fast at it and precise.
I've do e baseboard too. We never worried about the round corners. We would do them with an extra little piece on the corner. 22.5° on the joints to go around the corner.

larryrice

Hi Doc. I will have to look for that Trim-Tex Marker. Thanks. I notice a lot of outside angles/corners 45's there in your project. Do you have short cuts for coating? Can you run a small box across the outside angles? Thanks. Keep doing Great.

cmlet

I just mud the metal bullnose on then skim coat it then put paper tape on the corners so it cover the gap where the top and sides meet then skim coat over the corners and tape again then bam looks nice 👍

Beaterspanx

Thank you awesome display functional 🤙

danielbaldomro

I have to ask, would you recognize a box for repair work?

k.p.c

i just use a 2x4 with a 3/4" radius routed on its side attached to a miter saw. Tried that tool takes too much time miter saw a lot quicker

bjdrywall

For a novice/ dummy DIY home owner you went too quick with with the miter tool.
Home depot don't carry anymore. I found on line and bought 2.
I am terrible cutting the 45° .
Using the yellow handle cutter.
I like your hopper. I will shop for it. I have had a great deal of trouble finding bullnose tools. I found it is cool to do bullnose.
Thanks

jeannieblake