Homemade 50cc TRIMMER Chopper BIKE !?

We made something useful out of an old bicycle! Enjoy the new video!
.
#bike #50cc #trimmer #homemade
.
.
.
.
Photo equipment
-SONY A7III
-SONY 18-70
-SONY 18-200
-2x Nikon d3200
-Nikor 18-55
-DJI Ronin SC
-RODE
-RODE NT-USB
-GoPro 7 silver
.

[ysteinkaino]

This is cool for all boys and men between 0-100yrs.

[bastiaoemmiami]

Čestitamo učitelju! Hvala na ovom savjetu. No ja bih stavio oslonac za noge ispred motora, da noge budu ravnije.

Edit. (Here in 🇧🇷.)

[stevantrninic]

That's great guys in comments doesn't understand that engine power ISN'T speed, speed is in transmission, so you should put smaller cogwheel.

[octaviomarquez]

AMAZING.. I WAS EXPECTING SOME LIKE THIS... THANKS DOCTOR🙋🇨🇴💚

[unvchrm]

You use this machine, right? This machine is a 50 cc grass cutter. You must mix 2 coats of oil, also known as auto-loop or engine oil for 2-stroke machines. This machine is a 2-stroke engine.😊

[rackoix]

I think the gearing is messed up. The driver looks OK. But it should go directly to the rear wheel with 40+ tooth sprocket.
I can't fathom right now, how the large crank sprocket to another large sprocket at the rear works. I guess the engine is cranking the cranks to crank the wheel.

[kaptein]

Wouldve been quicker if you skipped the engine and left the pedals on

[kipwyand]

Nice job but If the 2 front sprockets were switched, I suspect it would be much faster. It would greatly lower the gear ratio allowing the clutch to hook up and engine to rapidly gain rpm with ease. As it is, the clutch will burn up fast trying to lock up the clutch drum. That can't happen because your gearing is way too high.

[danicao.]

Bravo majstore, bravo doktore!!! Još samo da ga ofarbaš u boji plamena vatre koja se prekida na pola rama!!! I mesto gde stavljaš noge mora biti još napred kao kod pravih čopera!!!

[ปลาตะเพียนนัมเบอร์วัน]

Wow, this is great. It's very beautiful. It's a self-made motorcycle. It's creative. When people don't have cars, we can drive this car ourselves.😊❤❤👍👍👍👍👍

[bryduhbikeguy]

Nice looking build, and a great idea.A bigger sprocket to take the power from the clutch will allow it to grab and increase torque./Lijepa konstrukcija i sjajna ideja. Veći lančanik za preuzimanje snage od kvačila omogućit će mu grabljenje i povećanje okretnog momenta.

[haugstule]

Since you show us such chad moves as to hand-center two sprockets and weld them, it doesn't shock me any less that you didn't just weld the big sprocket on the wheel and put a smaller one on the crank so the gearing would be closer to right the first time.
this gearing eats almost all the power this poor weed-wacker can produce boi.

[Abnubad]

Good job but you should put mud protectors and a cover for the rotating chain and I repeat very good

[piciuflorentin]

I would recommend a muffler on it, so the gasses won't be directly in your way! 👍

[hafizmo]

Nice work, can you show us this bike how it runs up hill?

[moatazballah]

It's not the best thing, but it provides fuel and physical energy..😃

[pjdonovanify]

I have the same chopper but with a 2 stroke, goes 21 mph. Not sure how you made it run so slow but yea.. I could walk faster than that

[yodaco]

Did we weld this plate directly next to a fuel tank with petrol inside. yes we did.

[diyathomevn]

Great video thanks, the bike is beautifully done.👍

[halogenisys]

Why not build a mountain bike transmission from the engine to the transmission to the rear wheels?