SUPER SUPER Simple Dovetail Joint

In this video I show how to make a dovetail joint on router table with only one router bit. As for me this is the simplest method.

All plans I ever made I collected in one place. Save this link for future - I will add new plans to this collection and don't forget to subscribe to my channel to stay tuned.

Support GRINwood:

Thanks for watching and hope this video was helpful.

GRINwood shop:

Follow GRINwood:

Music:
Parasail - Silent Partner

#woodworking #diy #GRINwoodtools .

Would you like to use my videos in your media projects?

[GRINwood]

All free plans I ever made here:

GRINwood shop:

Support GRINwood:

[mikeromeo]

Great, a nice improvement would be to make as many spacers as needed and number them, that way there would be no need to think about the order and there would be less chance of error.

[XxBloggs]

This would be a lot better if it had a voice explaining what is going on

[phillamoore]

I’d have to watch this 20 more times to figure how he calculated getting those to match up…..but, it was beautiful to watch!

[thantran]

What do you means to post video clip for ?You want people watching your job ?or you show people how to do it ?

[АндрейИванов-оял]

👍 Отличное исполнение! А я всё ждал, когда будет подрезка углов стамеской. Недождался! 😊

[Sixxiron]

Incredible but almost impossible for mere mortals with beginner tools….

[jamesnasmith]

Your spacer formula is clever. To describe the half-pin spacer size, some might find “half as wide” more intuitive than “twice as small”.
But your fence-referenced sled is equally clever; totally free of limitations imposed by mitre gauge track locations. Bravo to both!

[michaellionart]

I was about to ask a question but then you answered it at 5+minutes. Thank You

[wilarguello]

Ésto si me gustó, lo estudiaré para practicar.
Gracias, desde Nicaragua.

[АлександрФишман-шт]

Куплю на пару миллионов оборудования и начну "по простому" хвосты резать. Чувак красавчик конечно.

[danmays]

I agree with John Heisz. The only comment I have for improvement is to use either a digital or dial caliper to show your measurements. I realize that you are located in Ukraine, but these are available at really cheap prices here in the states. In the video, I am just not able to comprehend the measurements quickly enough. With this minor exception, you have certainly simplified the process of making this joint. Good job! Now I just have to go back and replay until I can figure out the caliper measurements. 🤔

[Сергей-пзп]

"Прлстой способ"- постройте мастерскую, купите оборудование....
Серия про простейший способ будет видимо с роботами. Просто дайте роботу деревяшки...

[jimmartin]

Brilliant! You've convinced me to try half blind dovetails. I've always done through dovetails with a false front. With a narrow bit like those for WoodRat this could make stunning drawers. Thank you!!!

[ИванБровкин-хз]

С таким количеством прибамбасов и безрукий сможет. Да и не так уж и просто, как в заголовке. Досточки-проставки попутал и пиздец заготовке.

[CarmoniusFinsnickeri]

Make a notch in the stop block or put it slightly above the table so the dust can pass under it, then you don't have to make the same cut 3 times, backing off to clear the dust.

[MCsCreations]

Oh... That's brilliant, dude! 😮
Thanks a lot for the tips!!!
Stay safe there with your family! 🖖😊

[Gennady_Sereda]

Спасибо за видео! Нужно взять на вооружение! 👍👍👍😉

[vvitchdoctor]

That was amazing. I love that spacer technique, really well done!

[babatrlalan]

Very nice!
A question: can the joints be done on the inside of the working piece, i.e. not to be visible from the outside, as seen on 4:44?