Easily Cut Plywood With This Tool

Показать описание

📷 by @shanty2chic

Kreg Tool

Рекомендации по теме

Комментарии

Next time get a 4X8 sheet of exterior foam board and use that to back the cut instead of 2X4’s just set the blade shallow. The foam board can be reused many times afterward as the cut line will be very shallow. After your cut in the video there was tear out.
You also can kneel on the sheet as you cut it to be more comfortable with less strain on your back.

clintprice

Best tool ever for rough cutting full sheets for table saw. Yes there are other ways to do it but if you set it up correctly and don’t rush, damn accurate cut. Spread the word, girl!

danielmcgrew

I would like to see how she finished that cut.

johnhumcke

And this folks is how you kick back and lose a finger, shocked kreg still has this video up can get alot beginners hurt

bwxfyrm

The 2x4 under the sheet of plywood need to go perpendicular to the cut you want to make. Set the blade depth 1/8” deeper than the thickness of the plywood. This prevents the plywood from collapsing and pinching the saw blade and that nasty tear-out I saw in this video at the end of the cut.

bdog

I just clamp a thin 4' metal straight edge on and run the saw along it but if that track and kit is cheap id buy it. What's the cost and where do i purchase?

cwatson

Does she have go go gadget extendable arms to reach all the way across that cut?

mikew

Blocks closer to cut line prevents binding

VMa-mqpm

Thank you !!! I saw this tool at the hardware store, but hadn’t checked our everything. I was directing myself to a table saw. You just saved me money. With this tool I’ll be able to maneuver the circular saw straight also.

EMC

BECAUSE OF YOU - THIS 71 YR OLD WOMAN IS GOING TO BUILD 2 FREE STANDING CLOSETS AND 2 FREE STANDING SHOE CLOSETS . ALL OF MY 8 ' TALL DR'S HAVE BEEN DELIVERED ALONG WITH MY BOUG'E AUTO OPEN SAW HORSES. TIME TO PURCHASE ALL OF THE KREG PRODUCTS NEEDED NOW AND FINALLY - HAVE ALL OF MY 3/4" PLYWOOD DELIVERED.... SO EXCITED TO GET STARTED.. AFTER SEEING THIS VIDEO I WILL ADD THIS ITEM TO THE PILE ...LOOK OUT IKE HERE COMES NENE TO SHOW YOU HER SKILLS WITH THE REAL SOLID STUFF AND STILL AFFORD

poppy

You can't set two by fours and then cut in the center of it look at the giant sliver on the end of the cut you have to be closer to what's holding it up so you get a clean cut that could bind and jump back and cut your hand off

juliewigginton

Infeed stands and outfeed tabke. Husky has some and ridgid does as well they are cheap and you need them

Rvbeus

The 1st time u tried to cut it you were trying to rip it. Then u show it doing a cross cut. Dose the track extend to 8ft? Also it looks like the saw didn't cut the last 1/4 inch of the wood (the right piece had s dagger)

ericcash

Buying a track saw is the better Decision. A good one can replace a table saw.

CraigularjJoeWoodworks

Because she made the cut with 2=2x4s below the plywood spaced on the outsides of her cut. I guarantee the saw kicked back or the blade got bounded up when the cut came in on itself because of the placement of the 2x4s.
But they edited out that section of the vid but you can still see the plywood end cut splintered of at the edge because of the bind or kickback on the saw. I’m all about people doing things DIY but do your homework first before you shoot a advertisement video 😅 next time set the 2x4 on one side of the cut or 2 but they need to both be on one side of the cut that way when you make the cut the wood you are cutting falls away from the blade not fall into the blade and create friction 😮
Anyway cool tool

g-cgeneralcontractor