How to Install a Hot & Cold Bidet the Easy Way & Attain a Clean Butt

#DIY #bidet

This again? This is my first video of 2021? Yes, we're installing a "Trustmi" bidet again, only this time with 100% less soldering, and 200% cleaner buttholes. Apologies about the strange aspect ratio, I'm not really sure what happened lol.

Bidet:

Brass 1/2" NPT Fitting (get two):

3/8" by 3/8" by 3/8" tee with compression fitting (get two, assuming you have 3/8" supply lines):

30" Braided Steel line (if needed, or get your own length):

12" extension (if needed):

Teflon tape:

Disclaimer: I'm an Amazon affiliate. _
_
If you found this video valuable and wish to support the channel, below is my Amazon affiliate page. By purchasing anything through this link, I will receive commission at no extra cost to you. Thank you!

[realtyrocks]

This is brilliant. I was going to buy one to hook on my toilet but didn't like the idea of cold water. This has less exposed hoses and warm water. I'm sold.

[SerbanCMusca-utny]

You are such a king of your own domain!
I'm jealous.

[atreyuws]

We put an in-toilet bidet that has built in controls into our place back in December. Couldn't live without one after visiting Japan lmao. Ours is cold water only, because it draws from the tank. But it's more streamlined since our bathroom sink isn't anywhere near the toilet.

[antoniogalluccio]

Not only the tap must be closed but the extra pressure in the hose must be released by pressing the button. This will help the hose no to burst. If you want to, you can always add single or double check valves

[drumsticks]

You're an inspiration, excellent outro.

[chap]

Definitely, definitely fit double check valves to each of the hot and cold water inlets of the bidet unit! Not only will it stop cold water entering your hot water system (or the other way), it will *slow down* lethal germs from toilet water contaminating your whole house water system (including drinking water)! This can happen if the sprayer falls into the toilet bowl. For example, if kids are playing around with it. UK water regulations demand much more expensive protection than check valves to prevent such contamination from such sprayers. At least have the check valves for a bit of protection!

[bgcsno]

1. Install Teflon tape in same direction as tightening threads
2. Use an open end wrench my or crescent wrench to tighten water connections on the stops

[vanettagaines]

Beautiful job handyman, just a
Suggestion, on the inside of
Your drilled holes, how about
Some washers for cabinet
Protection, and contact paper
Or vinly tile inside bottom cabinet
And caulking, sm, leak protec...


Thk's 4 sharing your video
Very informative.

[antoniogalluccio]

How much did you pay for your kit? This is the most decent installation I have seen so far

[BenHur]

Our house has these but they're a very rare feature here in the UK. The idea comes from the middle East and the family who lived here before us was Pakistani.
I haven't been brave enough to try them myself. Do you use them before TP, or afterwards? What do you use to dry yourself? TP would disintegrate on wet skin, but you couldn't be sure you were clean enough to use a towel.
So many questions raised by such a simple video 😉

[-ud]

Very useful video
Thank u so much
What would u suggest in case the sink is far from the toilette chair?

[atiqulny]

I have added 1/2" backflow preventer to prevent hot water running in cold water line.

[maernettesfay]

Thanks man, my wife told me the cold to here so thanks.

I never used this tool, but planning to have it in my house... On which side should it be fixed, if i am right handed?

[MohammadRafiqAzam]

Hi, thanks for the nice video. I have an issue with my bathroom. My vanity is 10 feet away from the toilet seat. How to mount the bidet spray pipe externally along the side of the bath tub to the toilet seat? Also, how to buy the product set in Canada? Thanks

[joefiorino]

May I ask where you found the 3/8" female compression coupling? I can't find one anywhere. It's the one item you don't appear to have linked in your list

[empireautomotiveservices]

Awesome idea!! Thank You and God Bless!

[hakimvlogs]

How would this work fitting on a solid wall that will be tiled over, my builder said it’s not possible, I said it is.. he ended up not fitting it

[jamesk.]

The union you used is npt on both ends but the valve is bsp g thread. It doesn't leak?

[leonyrey]

in order not to mix the hot and cold to your whole house you need to add a check valve to each supply line (to answer the question at your 12 min mark on video)