BIGTREETECH TMC2130 V3.0 , TMC2208 V3.0 ,The strongest TMC2208 and TMC2130 in history？

Parameter information：

Aliexpress :
BIGTREETECH Global Store

BIQU Global Store

BIG TREE TECH Store

BIG TREE TECH CO.,LTD

Creation Unlimited Store

[fortheregm]

finally a stick with proper heatsink space. thank you

[gloob]

Would be nice to see a comparision with the TMC5160

[Lennypl]

Too many film effects for not having enough zoom on an important element in the future please :-)

[misadventuresindprinting.]

You make a pretty looking video. Most people came here because they thought you were going to, well talk in your video. Watching you do stuff with no comantary is useless.

[АлександрПолотенчиков]

Skr v.1.3 tmc 2208 Uart I did everything according to the instructions! 13:48:35.855 : Testing X connection... Error: All LOW
13:48:35.877 : Testing Y connection... Error: All LOW
13:48:35.900 : Testing E connection... Error: All LOW

[ora]

did everything according to your guides and getting TMC Connection Error
SKR 1.3
Bigtree TMC 2208

[avexoidavex]

I bought four TMC2208 v3.0 UART. In this video they are connected via UART without wires. Why did BIGTREETECH send me one dupont wire 'mother-mother' to each driver? Where could I use this wires?

[CharmandrigoGG]

You only need one wire? Everything I have seen out there shows two wires and one of them has a 1k resistor but on the MKS Gen part it's only wired with one cable

[sdsfaf]

Is there any example of how to connect them standalone to an Arduino? Thanks

[mareklorenc]

I do have some device running on A4988 stepper driver, and would like to replace it with TMC2208 due to noise of old one. I bought TMC2208 V3.0 as I can se in UART mode. My arduino program doesn't support UART control. So Should I de-solder J2 jumper to use it as regular A4988?

[patrickconsorte]

is the TMC2208 V3 works with the Tevo tarantula pro?

[Thomeeque]

So PCB has 51C and chip only 36C (at 2:35)? That is quite weird..

[rodrigooviedo]

I have a doubt, i have installed the btt srk 1.3, on a custom made printer, with tmc2130 v3.0, i didn't make any mods to the TMC, cause i did followed this tutorial. Once everything is configured and calibrated, i can't put the printer, in printer position. It can be configured an area of impresion? i ask this because my printer is not in boundaries that leads it to the printer position in a mandatory way. So. Do i need to configure something else in the marlin? i have configured the HOMING_BUMP_MM { 0, 22, 318 } cause my Z starts to print up, and my Y have to be corrected to the 22 mm, from the origin.
But anyway, when i hit home in the printer menu, it goes Z=13, X = Y = center. The bed never is not nearly close to the printer head.

[colinraines]

Are the TMC2208 uart ready to be installed without having to solder the pins

[marcelrios]

Hi, they have some tablet that indicates vref in Tcm2208 v2 for different engines

[thorherz]

hallo ihr video gesehen was ist perfekt stepper strom tmc 2208 unart skr1.3 mfg

[wrxsubaru]

do you have to use those extra pin/wires on mks gen L? what is the difference in the versions anyways? i see 1.2 1.3 2.0 3.0 but i dont understand the difference in them

[wrxsubaru]

can you run the tmc2208 in 1/32 microsteps or higher? what do i need to do to accomplish this besides changing the steps in marlin? What jumpers do i need to remove?

[Zattoo]

dont understand the current and Vref things in my case tmc2208

[tonign]

Hi, I have problems with BIGTREETECH
TMC2130-V3.0 ISP mode on XYZ axes (0xFF: FF: FF: FF Bad response!) And BIGTREETECH
TMC2208-V3.0 UART mode on the E0 axis (0x00: 00: 00: 00 Bad response!) ... with the MKS Sgen L v1.0 board ... on the board the jumpers are in SPI mode and marlin configuration like SGEN_L Motherboard Datasheet ... help please!