Chamberlain 953EV Garage Door Opener Remote Programming Video

Programming/install your Chamberlain garage door opener Keychain Remote with Visor Clip (953EV/EVC) with this easy to follow video. LiftMaster remotes use the same programming steps. See chart below for extra information.

Get a Chamberlain 953EV remote RIGHT HERE!

ID CHART
Color of Learn Button

Frequency

Number of Presses

Yellow

SEC+2.0 Tri-band (310Mhz, 315Mhz, and 390Mhz)(Rolling Code)

1

Purple

SEC+ 315Mhz (Rolling Code)

2

Red/Orange

SEC+ 390Mhz (Rolling Code)

3

Green

Billion Code 390Mhz

4

1. Take the visor clip off and use the clip to press the program button on the back of the remote until the LED light on the front of the remote turns on.

2. Press and release the learn button on the garage door opener motor.

3. Press and release the remote button you wish to program ___ times, as indicated above.

4. Press either of the other 2 buttons on the remote to exit programming mode.

5. Press the programmed button to test. The door should activate.Chamberlain 953EV 3 button visor style remote. Program three different Chamberlain remotes into one unit. Works on all Liftmaster, Chamberlain, Sears units from 1993 to present. Chamberlain 953EV 3 button visor style remote
Program three different Chamberlain remotes into one unit.
Works on all Liftmaster, Chamberlain, Sears units from 1993 to present
product substituted with equivalent Liftmaster professional unit
Longer range
LED signal
Easy programming
Includes Battery

If this video was useful please give me a LIKE!!

This video was edited with Wondershare Filmora

[garagedoorgenius]

If this video helped you out and saved you a service fee, please feel free to SUBSCRIBE to my cause.
I'd love to hit 100k subs before Im 90 years old. 😂

[StevenBanks]

I’m just saying what everyone else is saying. Concise, accurate, no extra steps of cute commentary. ALL the other videos and written instructions were ambiguous or misleading.
I followed your clearly shown and described steps and in literally 1 minute I had a working remote.
Thank. You.

[kayeles]

I know this video is 6 years old, but YOU ARE THE MAN. I've watched so many videos, and none of them worked. I was missing the program the remote portion. Once I did that for a red button, it worked. A thousand thanks

[susanstelzer]

You were MUCH easier to understand than even the CHAMBERLAIN site! I was going in and out of the house to the garage trying to understand the instructions. I thought I'd try another YouTuber, who speaks ENGLISH! You Done Good!

[R-mn]

This guy did a great job. I programmed two remotes in less than a minute. There was no fluff, right to the point.

[lisatrace]

Thank you. Wish I had started here. Spent 2 hours trying to get the remote and opener connected yesterday, was ready to return the remote. Watched your video, not even to the end, and in less than 5 minutes I was up and running.

[gregcabral]

This was a great help. Others failed to point out the button under the remote clip. This step was not mentioned in the owners manual of cheap remote. Thank you very kindly

[tammytorbert]

Thank you! I have been getting out of car for two years. MN winters no less. Was at Home Depot and stumbled across the garage door openers. Instructions in the box were not clear. Found your channel and wa la - 2 openers programmed in 2 min. Thank you !!!🎉

[leesecanadian]

OMG I've been fighting with the supplemental remote i bought for this system for 6 months. Read the manuals watched other videos but nothing worked. Your video solved my problem in under 3 minutes. THANK

[whysguy]

Thanks! That was SO much simpler than that truly horrible Chamberlain video (which was so busy qualifying everything that it was impossible to follow). Pretty straightforward when you get right down to it:

- before you start, identify the wire/button color on the opener (purple for me) which will determine the number of presses below
- put the remote in program mode by pushing its program button
- press the remote button you wish to program the number of times needed (2 for purple), then press another button
- on the opener, press the learn button
- on the remote, press the same remote button as above (the opener light should flash)
- additional remote button presses should open or close the door

[memadelrey]

I couldn't have done this without your video. I am almost in tears. It's very hot here in California and I was getting frustrated. God bless you. Have a wonderful day

[carlowehermosa]

Thank you very much! It’s quick and easy…disconnected the remote to connect the garage door to my car…now had to switch back to remote!

[NorCalGal]

God Bless- thank you! You saved me on a day I had zero patience left!

[cin]

The most helpful and easy to follow tutorial ever!!! Took me less than 5 mins to do. Thank youuuu!

[kwawesome]

You rock man! The pre-programming setting of the remote by pressing the back button and using the chart with the color code and the amount of clicks is what I was missing.

[dannyd]

Huge thanks. The garage door at my other place took 15 seconds to program. At my new place, I couldn't figure it out for the life of me. I remember it being an easy process, but didn't recall exactly what that process was. This video came through. One thing I messed up on was the color. The light was kind of a tennis ball color. I figured that as yellow, and kept trying to press one time. No luck. Then it hit me that it was green. Tried pressing 4 times, and viola!!!!

[WnTonSoup]

Your video was much more helpful than the official chamberlain video, good job 👍

[sherreemccool]

By far the easiest DIY video! Thank you so much 😊

[willytwo]

Thanks for the detailed demo. I tried to follow the instructions to no avail. I think I was clicking too fast. You showed how to click, wait and click. Nice job!

[princehannie]

i am now a runner up master of garage remotes, all grand thanks to you!