Arduino LED blink using millis with different ON and OFF time - Robojax

Показать описание

Turn LED ON or OFF using millis() function without delay in Arduino. We can have different ON and OFF time.

The best thank you for me is to not to skip ads and Subscribe 🔔 to my channel, like 👍 the video It is greatly appreciated. 🔔 😊.
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe and enable the bell 🔔.😊

آشنایی با ملیس به فارسی

Jump to different chapters of this video
00:00 Start
00:30 Introduction
01:11 Wiring Explained
02:03 Code explained
06:33 Demonstration

Related videos:

Tutorial by Ahmad Shamshiri form Canada
****************************
****************************

Get other projects code and learn Arduino

#robojax #robojax_timer

Рекомендации по теме

Комментарии

To the point on the code and circuit, which is modifiable for other uses. This will work great by using the LED output to trigger on and off my relay circuit to turn on and off my hydroponics water pump at different on and off intervals. Thank you Robojax for helping to make the world a better place by sharing.

stickbug

thanks, you saved me again; didn't know how to get the LED set to high on boot :)

Gocast

I was searching for a looong time, thank you!

BroBZH

Thank you for your video. Really very helpful! I "translated" this code, once undersood how it works, to a micro:bit board.
Again, thanks for sharing your knowledge.

qcelma

Hi Robojax.
been watching all your videos in youtube. and its a big help for me as a beginner.
now im stating to study the millis fuction using led blink.

in this video just want to ask. if i want to make multiple led using this code. that it means i just need to copy the same code multiple times?

chuicoevenmerk

thank you very much Sir your tutorial was very helpful!

justicetom

Thanks for wornderful tutorial. This I want. Also pls let me know how to set led with blinking like Aeroplane light like two short blink and a long off .. like this.. pls awaiting an early reply.

letsplaytogether

this video concept ok sir. including one push button pressing this led glowing for on & off video uploading sir.

sarathigayu

thank you for the video it helped me a lot. can you make a video if I tell you for little project means basic circuit

qasershah

Can you make a video on how to use coin acceptor/slot that accepts diiferent denomination, add it and remember with arduino uno? Thanks.

anythingunderthesun

Great tutorial 🙏 just wondering if you’d give a private lesson (online) on an issue I’m having surrounding this? I’d be happy to pay for your time, thanks

AntonLock

Adding millis every completed loop, and not reset them, isn't going to overflow at a certain time ?

sfour

What do you use to set up your recording equipment to make the video please?

islandaloha

, thank you for sharing a video Mr. Robojax. I will try your code in my Arduino. Can I ask you if the Arduino can do by two loops in millis and can put some pinmode?

josephdesuasido

I am trying to fire a fuel injector and then fire a spark coil. I have found linear programming not suitable. I have attempted to modify your program, it loads but the timing seems not accurate/random have you done a video or a sketch to use two leds at the same time.

Graemecns

Could you form how to cause the LED to blink 6 times then stop. also to stop and go to a second led. Thank you

salc

Mr. what would i have to add if i wanted the led to turn in for one minute every ten minutes. Also add a button so that if the button is pressed during the ten minutes it will turn on for one minute. Thank you in advance.

truthseeker

how do I modify the code to run 2 LEDs „indipendently“ from each other with different on and off times?

emilbree

I was wondering how I could use Millis in my Arduino plant watering system, so it tells me when it was last watered? Any idea RoboJax?

r-_

Hey I want an led turn on and off I.e toggle for 2 minutes and then stop. but without delay function and and if I interrupt it should stop I.e reset. What code should I use can use suggest me

Tubeunus

Arduino LED blink using millis with different ON and OFF time - Robojax

Arduino LED blink using millis with different ON and OFF time - Robojax

Arduino Blink without Delay

Arduino Sketch with millis() instead of delay()

Arduino Chasing a LED with Millis

How to do multiple tasks in Arduino | Beginners | millis() function

Lesson 62: Time control without delay, LED blink with millis() | Arduino Step By Step Course

Tutorial: How to use millis | Goodbye delay, Hello millis

Turn An LED On and Off At Different Times With Millis

How to Use Millis to Master Arduino Multi-tasking

How to use millis() function to multitask in arduino code.

LED Blink using millis

Arduino Random Multiple Blinking LED's Without Delay using millis

Using millis() to add a timer

Arduino Multitasking tutorial to use millis() in Arduino Code

Arduino Tutorial on Using millis() to Blink an LED While Doing Other Stuff

How to Fade LED with millis function | Arduino tutorial for beginners

Arduino UNO R4 Lesson12 - millis Function | Handling Multiple Tasks | Non-Blocking Code

Tinkercad | How to blink LED with out delay () 💯| LED blink without delay Arduino | Millis()

Lab 1 Using Delay with millis

Arduino basic ep.1: Replacing delay() with millis()

Arduino: Blink LED with different on off times just once with millis

Arduino - Multitask Your Programs - Example with 2 LEDs Blinking at Different Rates

Traffic Light w Walk Button using millis() Arduino code included

Morse Code SOS Flasher Using Millis with Switch | Arduino