Beginners Guide To Klipper On The ELEGOO Neptune 3 Pro

LINKS

#3dprinting #klipper #neptune3pro

[郑天-fi]

Guys I just found out how to do the levelling part, here to share the way.

1.First we use: BED_MESH_CALIBRATE
SAVE-CONFIG

2. Then: set the Z-offset
Code: PROBE_CALIBRATE
TESTZ Z= (+/-value)
Then TESTZ Z=+ or TESTZ Z=- to "bisect" the last position - that is to move to a position halfway between two positions.

Finish: Accept

[sabotaged]

Amazing work! FYI it works with Pi Zero 2 W without any issues.

[DeadDealer]

Perfect timing!
Next week my new Neptune 3 Max arrives, and I have a spare Raspberry Pi here. Thanks for the video! 🥳

[interdimensionaleagle]

perfect, I have a raspberry pi 3 B not being used. going to start this upgrade right meow

[spoonmanxx]

I just bought a Neptune 3 Pro. I'm thinking about upgrading to Klipper, but I just realized that if I put Klipper on the printer, what settings should I have to change in my slicer?

[trebory]

So I'm having an issue with the whole "...and adjust your z-offset accordingly..." part. haha How?

[jonathantenorioerebus]

does this work for Neptune 3 Max? i've see that theres one folder on GitHup page for neptune 3 max which only contains printer.cfg but idk if this is the only file that i have to replace somewhere following this tutorial

[HelpfulHobbies]

This was really helpful! Thanks for these Neptune vids.

[trebory]

Hey! So this helps me out a LOT, so thank you so much for an easy to follow tutorial.

However my next question is what do other Elegoo Neptune 3 Pro users use to slice their files, and what are some good starting point Prusaslicer print settings to start out with?

[Vandius]

If you're having problems with z-offset, in the printer cfg set probe speed to 2, probe samples to 5 and probe count to 10, 10 then rerun calibration.

[KwadFan]

Want to mention, the URL depends on the hostname you set in rpi-imager. Thanks for the Vid, Regards Kwad

[retro_pollo]

Is there a way to make the screen work after we install the update? I would really like to have both worthing

[wesleydutoit]

My next big project!😁 I recently made a sick almost air tight enclosure, with a filtered exhaust fan. Now I can print a wider range of materials. What would you say is too warm for the components inside?

[darklordstudio]

I'm really thinking about upgrading my two Neptune 3Pro to Klipper. I'm so sick and tired of the steps I have to do, to 3d print on my N3P printers.

[Optikification]

Just got my Neptune 3 max yesterday and currently use octoprint and the thought of flashing klipper scares the pants off of me.
Would hate to brick it.

[DrexProjects]

I'm going to try this on the Elegoo Neptune 3 Max.
Wish me luck.

[williamgodfrey]

So I'm using the btt 7 pad with main said I got a question maybe someone can help me on here because it's the same printer and set up just - the pie but I'm having a hard time with prints not going to the bed like the printer head is printing far away from the bed I tried going and redoing the calibration on the bed mesh and on the nozzle sorry drawing a blank I been fighting with this probelm all day

[dcsechrest]

@TheFeralEngineer - First thanks for doing all the hard work for us!!
I am having an issue with flashing the firmware to my Neptune 3 Pro. I do the make and then the CP to rename the file to ZNP_ROBIN_NANO.bin. I then copy the .bin file to the sd card and put it in the N3P, turn it on and wait. after a min or so I turn the machine off and remove the sdcard. when I reboot, it still has the marlin firmware on it, not klipper. Any ideas what i might be doing wrong?

Thanks

[wescobb]

Thanks for this! Will it also work on the Neptune 3 Max?

[freebird]

Thanks for the video. Will like the creativity klipper pad work with the NP3 ?