Configure the EdgeRouter X SFP with Nokia G-010S-A GPON module

In this video, I will show you how to configure the EdgeRouter X SFP to work with the Nokia G-010S-A GPON module.

After watching this video, you will know
- How to setup Internet on the EdgeRouter X or EdgeRouter X SFP for first time use (PPPoE & DHCP)
- Configure NAT rule to access the modem (Nokia G-010S-A) which is behind NAT
- Clone the MAC address for WAN interface
- Enable Hardware Offloading on EdgeRouter series

If this is your first time using a GPON SFP module, please have check on the below videos:

Video timeframe:
00:00 - Intro - EdgeRouter X SFP & Nokia G-010S-A
00:29 - Hardware Setup
01:21 - Access the EdgeRouter X SFP Dashboard
02:23 - Edgerouter X SFP Initial Setup (PPPoE)
06:34 - Configure NAT rule to access the NOKIA G-010S-A
08:42 - Quick Overview of the G-010S-A Dashboard
09:33 - Clone the MAC address for WAN interface
11:12 - Internet is up - Let's run Speedtest
13:11 - Enable Hardware Offloading on EdgeRouter X SFP

- If you are interested in the EdgeRouter X SFP & the G-010S-A, please send me a DM

That is all for this video. Thanks for watching and see you in the next one!

[borngeek]

I recently got running with a different GPON SFP (not SFP+) in a UDM-Pro

Finally cracked it 😀

// Awesome videos. For me was clone Mac, serial and ploam as ppoe username 😁

[michaeljarcher]

Great Video, the tip about accessing the device on the WAN port is particularly helpful. I was running a 2.5 Fiber router (bridge mode) and a ER-X unit, but now I've upgraded to a (save's me a power socket) ER-X SFP and a ODI 2.5Module ( DFP-34X-2C2) been running sweet for a few days. Feel the ER-X SFP is a little better performance than the ER-X basic model.

[GpconnectInfohotspot]

would love to see this setup on a pfsense netgate appliance

[jonathanbuzzard]

Couple of points. Firstly as per the release notes ipsec hardware offloading does not work on the Mediatek Edgerouters like the X SFP when using EdgeOS 2.x Secondly you have an MTU of 1492 on your pppoe interface. Consequently, you want to set some MSS clamping "set firewall options mss-clamp interface-type pppoe mss 1452". Finally, you should not need to setup masquerading to access the GPON SFP if you configure things properly. It is a routing issue and no masquerading is required. "show ip route" from the CLI should show it as a connected route at which point it should work. Might be some artefact of the wizard, I have only setup Edgerouters using the CLI.

[gianry]

Hi, I 've appreciated a lot your video but I'm not able to ping the Gpon module. I'm able to ping the IP address of the same subnet added to the Eth5 port. I've created the NAT masquerad too. thanks

[Jassett]

Hi, how did you install openwrt? i have searched everywhere and i don't see how to install it on this model, thank you very much.

[andrewsucre]

Can I use it with GPON SFP module but only as a switch
So all the intent traffic passes through edge router to my main router UCG ultra
Basically no routing/dhcp/nat/firewall?

[pashachoo]

Hi, i have a question
If i turn on hardware offload, and turn SQM, will hardware offload turn off automatically when sqm - on?

[rubas]

Hello
You could make and upload one with the HSGQ XPON STICK module, but with a Vlan. Please.
Since in your video Configure the EdgeRouter I would appreciate

[ddsofiane]

thanks for this video, if its same with edgerouter 12P and gpon sfp ubiquiti?

[buildeverythingvn]

Liệu có thể dùng router nhà mạng fpt để làm convert quang được không

[philipjanbaruis]

Hello Van Tech Corner, can you do Lan port to Wan conversion in OpenWrt 22.03.5 ? I can't see any tutorials about that, since on that version there's no switch options in the networking settings. Hope you's see this. Thank you

[paulborza]

How configure Mikrotik hEX S with Nokia G-010S-A GPON module? you can help me with this problem??

[buildeverythingvn]

Nếu mình không dùng cổng sfp để quay pppoe thay vào đó dùng cổng eth0 được ko nhỉ

[cuongvu]

Can you help me vs
GPON ONU Stick with MAC SFP 1310nm-TX/1490nm-RX 1.244G-Tx/2.488G-Rx Class B+ 20km DDM SC/APC SMF Optical Transceiver Module
runs on edge router6p
I have set it up as you instructed but cannot log in to sfp

[CovaZombiesKiller]

how did you find the mac in part 9:35?

[jahidkhan]

Hope you are well? Please help me, I wanted a tutorial. I want to use 2 separate isp's broadband together, both ppoe connection. Using mwan3, loadblanching openwrt, with wire guard vpn I want to make it a completely different isp. You have earlier tutorials on this topic, but I want tutorials on latest openwrt's mwan3, load blanching, wireguard. My Router Model: Tp-Link Archer C6 V3 I am using openwrt on this router.

[JackBlack-jidh]

Hi. I'm newb in linux, and can't find problem solution: my xiaomi r3g v1 used for transmission + samba. I was made installation by official openwrt guide, but facing with several problems: 

1) transmission installing on tmp folder by default;
2) transmission and samba4 have issues with user-group (problems with deleting and moving files)
3) maybe [2] provide some problem with partition table - after ssd completely written once I can't delete and rewrite it (system think there is no space left).

I can't find solution and never heard about this problem. And pleas give advice about user policy to use with smb and transmission.

[danysaifuddin]

Where i can buy the Nokia G-010S-A SFP?