Car Shakes and Vibrate while driving. Always CHECK THIS.

This is a driveshaft guys, I mis-spoke during filming of this video.
Please NOTE: The bulk of my time in the comment section is spent on comments and questions from SUBSCRIBERS, If you not subscribed, or leave off the question asking are you subscribed, I have to get to those questions after im done with all the subscribers questions. Please understand, this very important. Also guys/gals, if you need to get in contact with me ASAP concerning info or help, please use the CashApp $20 donate feature to $JohnnieRayThomas. Simply donate and a message will come to my phone and I can get in contact with you ASAP, thanks. Or simply leave your comment or question in the comment section. Thanks for viewing an Online Mechanic Tips video with JT the Car Guy. As always ask any questions you may have but please consider subscribing to the channel because I speak about a lot more. Please use the donate links to my Paypal or my Cash App if you wish to donate and help support the Channel. This also sends a direct message to my cell phone alerting me of assistant needed quickly, which means I can get back to you quickly. Thanks in advance. If this video in any way helped you save time and money, please consider donating.
Cash App here: $JohnnieRayThomas
#jtthecarguy
#shorts
#driveshaft

[xion]

Bro, i swore you were speaking Japanese when the clip started.

[crazyman]

And the lesson is this: don’t buy Chrysler products. 🤑

[jasonpocaro]

Carrier Bearing. Most times it CAN be replaced by itself. You MUST "index" the drive shaft ends. If they don't go back EXACTLY in the same clock position? You'll "create" a vibration. 😫😬

[benohuigin]

It's called carrier bearing and I think those shafts can be separated

[robertarmstrong]

Dude I just ran across this video and just to save you guys some money I thought I’d chime in. The carrier bearing on bigger car and long wheel base trucks r 100% replaceable. U remove with a bearing puller and u gotta have it pressed back on. Good Luck !!!

[doza]

Did you just switch from Japanese to southern English my guy??😅

[macartzattack]

Commenting as a factory worker at a place that makes drive shafts for Ford, GM, BMW, Volkswagen, and Mercedes/Daimler, the piece that you mentioned wearing out is a sort of Center Bearing which can't easily be replaced on the actual shaft due to how it is installed (hydraulic pressed on with a protection cap, some parts have a yoke welded onto the end of it and then that is usually joined to another yoke with a star joint and four needle bearings)

[ABF]

See the boot underneath that bracket. Remove clip and pull it back. Shaft will disconnect to remove bracket.

[Big_Ben]

1 piece of driveshafts can vibrate, too. Out of balance or bad/defective U-Joints. Some driveshafts are defective right from the factory and just get worse as time goes on.

[trixieapril]

What you have there is the drive shaft out of an awd charger, and that bushing is called a center support bearing/carrier bearing, it can be changed out for a new one its just decently hard to do and takes time plus special tools. I have an 08 cadillac cts awd mine went out and i changed it myself just putting it on ramps in a gravel driveway, so you dont need a whole shop to do it, and its definitely a lot cheaper than an entire driveshaft 😂

[trashheap]

There’s a boot there? Separate the shafts and replace the bushing. Call it a day.

[Nick]

On my 2006 Mazda BT50, the centre bearing is replaceable. It unbolts once you have the uni joint off.

[deloriansmith]

Carrier bearing you can replace it. Upcharge to replace the whole axle. Carrier bearing is $45, machine shop will take it off for 15 and press new on one.

[rickylandry]

This is a very common problem on Honda CRV’s I replaced three already this year.

[fernesal]

Mine vibrate on floor and gas pedal. I'm not sure if it is motor mounts, cross joints, or differential gears.

[milkyway]

how would you know or differentiate the vibration coming from the transmission or tailshaft or centre bearing. my car start to shudder from 0-10mph

[mrk]

JT my man you must have a little Italian and you because you talk with your hands my Brother

[murrayrothbard]

The carrier bearing is easily replaceable. Might as well replace the u joints as well.

[mrk]

That's rebuildable an easy way to find out is look up the part and make sure it could be ordered for purchase but sure that is rebuildable

[Robert-fgxb]

What about vibration at idle with the steering wheel turned at 45°? (PLEASE ANSWER)