More torque . Better Hill climb . More power for take off . Variator mod scooter gy6 50 150

more torque equals less topend !

[leohobbleohobb]

i heard belt slip witch is common problem on many gy6 do to small diameter variator and clutch assembly.Stiffer tork spring in clutch assembly and balance that out with heavyer roller to create more pressure on the belt sides for better grip.Also go up from 18mm wide belt to 18.1mm same legnth and angle on sides, give a longer life before it slips again with stock weak tork spring

[Damian-Church-NZ]

Dude thanks.. ive just taken three weights out and now its going perfect.. wheelstands up hils.. legend Dude....

[mattewgrigg]

Did this on my gy6 buggy it help out a lot I had 13g rollers it was bogging up hills I put 3 6g rollers in it did better thank you going down hill with all the 13 g rollers in I hit 34mph now with just 3 6g rollers I hit 46mph down hill

[drdrew]

Cutting the weight by HALF is never going to be the right answer. You need to FINE TUNE by trying weights just a little bit lighter. Small adjustments are the key. Often need to mix 2 different weight rollers in alternating pattern to keep rpm in power band the longest without compromising top speed too much. Baby steps

[ShawnTheAffiliate]

Hey bro I have the same model scooter I was recently going 32 to 35mph around 2 days ago woke up went for a ride and now it’s going 20 mph regular even small hills it goes 15 miles up when it use to rip of hills? Do you have any advice what’s wrong could it be the air filter or carburetor or will something like this in the video be a fix. Give me your opinion

[Sidg]

In gearless scooters, should we apply little bit of grease on round shaped rollers and roller-grooves in variator for smooth spinning of rollers in variator?
Or will it make more issues after some time like dust deposit, sides of rollers get flat faster, vibrations will increase etc ?
Please tell what should we do with proper reason.

[KuldipPawar-py]

I have moterstar easyride 150. I change lining, spring of 1000 and 1200 central spring, and 12g balls. But still it does not claiming even simple hill. Can i know whats the problem with this and how can it repaired?

[smartunnel]

very impressive it does not vibrate at all. I have 2 different scooter (SYM & Yamaha). It will vibrate the scooter (move backward) when I give it a gas.

[cihaneker]

what would happen if i removed all the weights? Then it would be super light but the variator case is heavy. Do you think that the variator case is heavy enough to change the gears?

[lixv]

I have a Yamaha RayZR 125 bs6 so how much weight of rollers should l install? Also, do you suggest using Dr. Pulley rollers instead?

[valtteri]

Does bigger torque help you with wheelies? I have aprilia sr50 ditchet and it does not pop wheelies easyle i can wheelie yes but its really daem hard

[Akshayvp]

Bro i have a Suzuki access 125. I want more mileage. So what i can do for that

[mke]

I have a derbi senda 50cc 2003. The acceleration is extremely slow, can’t go up hills, only goes if i push it. What should i do?

[wadebarnes]

Shims for 50cc will do better. That's what I did my 50 now I'm catching hell finding shim to do a 150

[arunavasinha]

Bro, can you suggest me something, i was having issues climbing uphill with my aprilia storm 125, but after i used a stiffer spring with 3*20 gms rolls setup, i can see a considerable difference but will it decrese my mileage? Or breakdown somewhere in the middle of the road

[advvaibhavvashisht]

Will I lose any top speed on my 2005 model Honda activa 90CC scooty if I remove three rollers, it right now does 80 k/hr top speed?

[davesogn]

So I have a lance PCH 125 with stock 14 G if I take out three of them where would that help

[neilharding]

hi please can yo keep things simple for me, i have a small quad bike 100cc ...cvt drive ...i have no interest in speed but want to tow a small garden trailer, what can i do to make the engine not work to hard and keep the torque up

[Ur-notalonehere]

Will doing this cause any damage later on

[ElPatronGamefarm]

I have a 150cc go kart, goes about 35 currently, what is the best way to give it more torque and keep it about 30 miles an hour?