Concrete Block Repair Using Sakrete Pro Mix (Making Money!)

#EverythingAboutConcrete #MikeDayConcrete #SakreteProMix
This video will show you how to repair a hole in concrete blocks using Sakrete's Pro Mix all purpose cement mix.
How to repair concrete blocks.
How to fix broken concrete blocks.
This repair mix is good for all types of concrete repairs. Watch as I fix this vertical block with a big hole in it.

LEARN FROM ME - PRIVATE MEMBERSHIP AREA:

GARAGE FLOOR EPOXY FLAKE COATING COURSE:

MY STAMPED CONCRETE COURSE:

MY CONCRETE SLAB COURSE:

FOUNDATION CRACK REPAIR COURSE:

GARAGE EPOXY FLOOR COATING COURSE:

VISIT MY WEBSITE:

USE THE SAME TOOLS I DO:

36" MBW POWER TROWEL:

ScreeDemon Gas Powered Vibratory Screed:

Screedemon Battery Powered Vibratory Screed:

14' Screed Board for ScreeDemon:

MARSHALLTOWN SHOCKWAVE VIBRA-SCREED:

TOPCON LASER LEVEL:

DEWALT PENCIL VIBRATOR TOOL:

INVERTER GENERATOR LIKE WE USE:

BULLFLOAT:

HAND FINISHING KNEE BOARDS:

MAG FLOAT & STEEL TROWEL SET:

2" MARGIN TROWEL:

CONCRETE PLACER OR KUMALONG:

CONCRETE FINISHING BROOM:

CONCRETE SCREED:

CONCRETE EDGER:

CONCRETE GROOVER:

BOSCH HAMMER DRILL:

MY RECOMMENDED TOOLS PAGE:

SUBSCRIBE to my email list and get my FREE video guide on how to get the perfect broom finish on a concrete patio:

Follow me on Twitter:

Follow me on Instagram:

Follow my Facebook Page:

[joshieb]

Thank you for showing how to do this. It's a much needed repair in many older homes, especially from the outside where there was no water barrier prior to a certain year.

[myronsmith]

I do these patches all the time in warehouses from the forklift blades running into them . Nice job Mike

[jefff]

Thanks taking the time to create such a great video.

[richardoconnor]

Was that from ice popping or fork lift, because all that block in the area (white) is showing water damage. Here the building inspectors will jump all over that, make fix the water issue and replace all the blocks.

[T.E.P..]

this is a cool project for your channel Mike!!! you know i've been a long long long time fan and sub on both my UTUBE accounts. I say to all of you ... don't do that music over the work. Voice over or SPEAK to the project. The music is not a strength. You speaking over what people are seeing is the STRENGTH. not this general music. Hope you guys all have a perfect weekend. One of my fav channels.

[bonanzatime]

That patch certainly isn't going anywhere, especially with them screws in there. But as a mason, I would just throw some type S mortar in there, squeeze it up against the edges with my bricklaying trowel and then dress it up to look like block. Do that by rubbing it with a piece of block after it sets up a bit. Done in 10 minutes, start to finish.

[aussiecro.]

Mike, maybe a bit of 'light' on the subject would help us all...you included?

[moneen]

Great video! May I ask why you add the screws in the beginning?

[Mikidy]

nice job. But like Mike Haddock says "if you want to make it stick, you have to get it wet first."

[LadyLawAlly]

Can this be used to resurface the concrete wall?

[lfenrfm]

Awesome thank you i have an area ike this and i cant add block, fantastic work 😊

[yorselrus]

Should you use a wire mesh if it's at least an inch deep

[steelthunder]

I always watch videos so I can fucking read through the whole goddamn thing

[mattcasoni]

Why not use a little premixed? Expanding Foam to fill the hole and premix fill the rest. Exactly the same and less work

[herbeaversmels]

Wouldn’t recommend using the impact drill on the tap cons

[pitbull]

You could have cut the face off a new block then cut out the mortar bed and head joints and damaged block replaced with the new one and tuck pointed it back in.

[joeswheat]

And that's how you do a quick repair of damage caused by the fork on a forklift.

[BigMike]

That wall is crumbling because it’s under lateral pressure from water. While I applaud the repair, this is a bandage on a bullet hole.

[ricleroc]

His skin must be made of steel… at least on his hands.

[tevman]

Great techniques but, I don’t think I could afford the bill. So instead, I’d put a full size, cut-out, dart board figure of ‘O-Biden’, in front of the damaged area. Naw, I’d pay the bill first. Know what I mean! Again, great video!