How To Make Digital Temperature Controller

Hi friend in this video I have made an electronic component tester using arduino and a few more component I hope you learn something from this video please like share and subscribe

Components:

1X ARDUINO NANO

1X 10K THERMISTOR

1X 12V ADOPTER

PREF BOARD

JUMPER WIRES

Circuit Diagram:

Arduino Code:

Arduino File

Zip File

Text File

My Channels:

Previous videos:


#KiyanisLab #TempratureController

[MojsterMijagi]

hello! i have a question for your project. I am curious about your relays logics and how did you physically connected them. Which relays connector you connect voltage beacuse if i understand right the heating and cooling are diffrently connected(one is connected to normally open and one to normally closed)? otherwise cool project!

[vladimirvavrik]

Excellent construction! I made it. Just a small mistake. In the code, pin A5 is written, but in the diagram A0 is connected. After correction in the code everything works great. I have a subscription to your channel my friend. You're doing a great job. Greetings from the Czech Republic.

[MarloTechWorld]

Why did you put 4 push buttons but the diagram has only 3 push buttons? Which digital pin should i solder the fourth one?

[mbos]

Hallo Kiyani, er staan 3 Push Buttons op het schema. En U sluit er 4 aan. Ik neem aan dat de vierde is voor de reset.

[MaxGoddur]

How do you stop the temp from oscillating above and below the setpoint?

[gaidenlee]

Is their an insntance to make the limit temp value to be negative?

[sanjaybatra]

I have notice that 4 buttons have been used in code, but in your code and circuit diagram .. you have only shown three buttons ?
something missing ?
I don't understand the use of variable "m" in code.
when the value of "m" will reach 1 ? (m= 1), when we press button 8 and variable "x" reaches 300 ?? if(x==300)

it means loop() will complete 2 rotation and move to 3rd rotation.

please clarify doubt.

[dejanpetkovski]

Hi Kiyani's Lab i need this only fo heating controll did i must make a cooling too or not. Thanks

[panthLeoJTm]

Hi, Sir, I tryed to use the code you put below but It doent work. What is your advise to me?

[newvaper]

hello kiyani....thanks for the video....i am doing a diy smd hot air....the hot air handle has 2 thermocouple wires...how can i control the temperature of the heating element of the smd hot air blower? thanks.

[habilekgopti]

something is wrong bit you are the best youtuber up

[caturhermawan]

can the thermistor be replaced with a thermocouple?

[MarloTechWorld]

Sir, thanks for the video. Am only seeing the limit temperature, how can I set the minimum temperature? Or how will the cooler and the heater be turned on and off if you set the limit? I want to use this project in the egg incubator.

[hirdeshbajwa]

What is the temperature probe you used? I have the ds18b20

[pubgmobail]

My brother, I have implemented the scheme, but it is not working well. The temperature is 210. Can you help me?

[abeditani]

I like your channel because you making it easy and you do the project as you do it with out hide anything . 👏👏👏👍👍

[melplishka]

Very well done. Exactly what I was looking tyvm. Very well explained too.

[Aniketdada]

Bro i want to know how you connect heting device 💡bulb & fan to circuit

Please bro tell me how you connect💡💡💡 🥺🥺🥺

[musaberashid]

Did you program the arduino nano using a computer

[aanagasin]

Cool. Can be setting for ramp and soak program?